Full HD Video Conference Camera System, buy SMTSEC SVC-HD 610-DSYC-SE600 high quality Low Cost High Performance 3.27MP SONY 3x optical zoom HD video conferencing system on China Suppliers Mobile

Product Details

SMTSEC SVC-HD 610-DSYC-SE600 high quality Low Cost High Performance 3.27MP SONY 3x optical zoom HD video conferencing system

Product Description

Low Cost High Performance 3.27 M HD Video camera achieved 1080p@30 high quality images. Equipped with SONY 3x optical, 12x digital zoom lens with wide HorizontalView field, ideally for small-sized videoconference rooms, auditoriums, and classroom. DVI-I connector is suited for DVI-D analog component which provided high-quality digital display, and HD-SDI used for long distance transmission application.

Features:
cutting-edge High Definition PTZ camera
Fast and smooth video handling
Low cost design for marketing
Power ON-OFF switch
Work & Standby LED indicator
Speed Match
Auto/Manual focus/brightness/WB
RS-232C/VISCA Protocol
Lens/Dome OSD
Boundary scanning
Standby & wakeup status
Swap video format
DVI/HD-SDI Video output

Performance:
1/2.8" Type CMOS
3.27 Megapixel
0.25 Lux at F1.2
720P@30, 1080P@30
3x Optical x 12 digital zoom
f=3.0 to 9mm F1.2-2.2
HOV 90° degree
DSY Video output
Pan : 0-355°
Tilt: Up: 45°, Down: 45°
64 preset positions
4 cruise lines
DC 12V, 2A

Dimension:
L 250mm x W 140mm x H154mm
N. Weight: 1.23 kgs (only camera)
G. Weight: 2.4 kgs (one unit)
N.W Carton of 2 units: 2.6 kgs
G. W Carton of 2 units:5.5 kgs

Installation:
Desktop
Ceiling mount
Standard Tripod accessory

Model No.		SVC-HD 610-DSYC-SE600
Image	Image Sensor	1/2.8" Type CMOS
Sensor	Effective Pix	3.27 Megapixel
	Min. Illumination	0.25 Lux at F1.2
	White balance	Auto/Manual/Indoor/Outdoor
	Gain control	Auto
	Backlight compensation	On/Off
	Shutter speed	1/5~1/10,000S
	S/N ratio	>50db
Lens	Focus	f=3.00(wide) to 9mm(tele) F1.2-2.2
	Iris	Auto/Manual
	Lens	3 Optical x 12 digital zoom
	Horizontal view angle	1080p:90 degree,720p:70 degree
Video output		DVI,CVBS,HD-SDI
Signal system		720P@30,1080P@30
Control terminal		EIA/RS232C,EIA/RS485(Bidirectional)
Control Protocol		VISCA,PELCO-D
baud rate		9600/38400bps
patrol line		4 cruise sequence
preset position		64 preset positions
Speed Match		Pan/Tilt movement speed depends on camera module zoom in/out
OSD Menu		Access to OSD Menu and adjust camera module parameters
Image auto flp		Support Horizontal/Vertical image flip
Pan movement speed		1-200°/Second
Tilt movement speed		1-150°/Second
Pan movement range		Pan: 0-355°
Tilt movement range		Up: 45°, Down: 45°
Pan scanning automatically		Support Pan scanning automatically
Boundary scanning		0-359° scanning (programmable)
Remote controller		IR Wireless Remote controller P/T/Z
Power supply		DC12V,2A
Work Temperature		0-50℃
Humidity		0-95%RH
LxWxH		250mm x 140mm x 145mm
Weight		2.8 kgs

SMTSEC Video conference camera FAQ
Symptom	Cause	Remedy
The power of the camera is not turned on.	The supplied AC power adaptor is not connected to the DC IN 12V jack firmly, or the AC power cord is not inserted firmly into the AC power adaptor or the AC outlet.	Insert the power cord firmly as far as it will go.
The power of the camera is not turned on.	Not Turn On the Power switch as “ON”.	Turn On the Power switch as “ON”.
Insufficient frame rate detected	Cannot recognize USB 3.0 connection, but the USB 2.0 speed.	Make sure you connected USB 3.0 Cable, USB 3.0 connect, and firmly connect to USB 3.0 interface.
Pan,tilt or zoom cannot be operated.	Any menu is displayed on the monitor screen.	Press the “Dome OSD” OR “Lens OSD” on the Camera remote control Unit to turn off the menu from the monitor screen.
Pan,tilt or zoom cannot be operated.	The panning or tilting range is limited	Pan/Tilt movement range is ± 45 degree.
The Remote Commander does not work.	The Camera Select button you pressed on the Remote Commander does not match the number set with the IR SELECT switch on the camera.	Press the Camera Select button corresponding to the IR SELECT SWITCH setting on the Camera.
The Remote Commander does not work.	Used out of battery	Change new battery (AA x 2)
The VISCA control is not available with a computer connected to the camera.	The computer is not correctly connected to the camera.	Make sure the connection between the computer and camera is made correctly.
	The computer is not correctly connected to the camera.	Check that the VISCA control setting (RS-232C or RS-422) and the baud rate setting (9600 bps or 38,400 bps) are properly made with the BOTTOM switch on the bottom of camera and the COM Port which configured in your computer.
The camera cannot be operated at all.		Pull out the plug of the power cord from the AC outlet, then reinsert it into the AC outlet after a while.

SMTSEC Video conference camera FAQ
Symptom	Cause	Remedy
The power of the camera is not turned on.	The supplied AC power adaptor is not connected to the DC IN 12V jack firmly, or the AC power cord is not inserted firmly into the AC power adaptor or the AC outlet.	Insert the power cord firmly as far as it will go.
The power of the camera is not turned on.	Not Turn On the Power switch as “ON”.	Turn On the Power switch as “ON”.
Insufficient frame rate detected	Cannot recognize USB 3.0 connection, but the USB 2.0 speed.	Make sure you connected USB 3.0 Cable, USB 3.0 connect, and firmly connect to USB 3.0 interface.
Pan,tilt or zoom cannot be operated.	Any menu is displayed on the monitor screen.	Press the “Dome OSD” OR “Lens OSD” on the Camera remote control Unit to turn off the menu from the monitor screen.
Pan,tilt or zoom cannot be operated.	The panning or tilting range is limited	Pan/Tilt movement range is ± 45 degree.
The Remote Commander does not work.	The Camera Select button you pressed on the Remote Commander does not match the number set with the IR SELECT switch on the camera.	Press the Camera Select button corresponding to the IR SELECT SWITCH setting on the Camera.
The Remote Commander does not work.	Used out of battery	Change new battery (AA x 2)
The VISCA control is not available with a computer connected to the camera.	The computer is not correctly connected to the camera.	Make sure the connection between the computer and camera is made correctly.
	The computer is not correctly connected to the camera.	Check that the VISCA control setting (RS-232C or RS-422) and the baud rate setting (9600 bps or 38,400 bps) are properly made with the BOTTOM switch on the bottom of camera and the COM Port which configured in your computer.
The camera cannot be operated at all.		Pull out the plug of the power cord from the AC outlet, then reinsert it into the AC outlet after a while.

Packaging & Shipping

China Post (10-30 days)
EMS (5-15 working days)
DHL (3-5 working days)
UPS (3-5 working days)

•The most reliable, affordable way of shipping method deponds on your address.
•Online tracking number will be emailed to buyer through email.
•We dont take any responsibility for any custom delay.

Our Services

•All products have been checked and packaged in good condition before dispatch.

•All products have 1 year warranty.