Specifications
They are a self bunded double wall design which can be transported and relocated easily.Detailed Product Description
They are a self bunded double wall design which can be transported and relocated easily.
The Intech ITP range offers self bunded storage tanks for combustible liquids as well as other non – hazardous liquids up to 90,000 litres.
The ITP Series is a premium fuel storage solution designed for harsh operating environments with minimal site preparation.
Pressed corners and a reinforced top means a robust tank for your fuel storage needs.
The main points in this design is greater capacity for safe fill - sloping floor for water collection and ability to see under tank
The tanks are constructed to international ISO container footprints for ease of transport and transfer. The standard footprints are 3, 6, 12, and 14 metres utilising the container lock dimensions. This means these tanks can be transported without the need for specific costly logistics.
The range of tanks are primarily designed for the storage and dispensing of combustible liquids. The storage of Flammable liquids up to 55,000 litres can be accommodated with the relevant venting and accessory change. Remember to check your local regulations.
Main Specification
o Fill point pipe work, valving and connections.
o Pump bund with optional lockable doors.
o Mechanical overfill protection valve and electronic overfill alarm.
o Venting for tank.
o Access ladder and platform.
o Calibrated dipstick.
o Anti syphon valve.
Model | Standard SFL | Length | Width | Height |
ITP 31 | 30280 | 2438 | 2896 | 6058 |
ITP 69 | 67120 | 2438 | 2896 | 12188 |
ITP 75 | 72450 | 2438 | 2896 | 12191 |
ITP 85 | 81880 | 2438 | 2896 | 14630 |
ITP 90 | 87690 | 2438 | 2896 | 14630 |
Note: ITP-75, ITP-90 are bulk tank.
Whilst tanks can be set up specifically to customer requirements, below is the generic detail specification of the standard tanks.
Incoming Fuel/Product
o 80nb tanker fill point.
o Fire safe flanged ball valve, camlock adaptor and cap.
o Non return valve.
o Mechanical overfill valve
o Internal pipe work.
o High level alarm – hazardous rated, battery powered.
Outgoing Fuel/Product
o Anti-siphon valve (foot valve)
o Pipe work terminating under walkway.
o 6inch Sockets in both manholes for the mounting of submersible pumps – standard.
Pump bay
o Bunded pump bay complete with water / product drain valves.
o Internal access for hoses from pylon kits.
o Pylon kits with counter weights (optional).
o Lockable bund doors.
o Access ladder to work platform either mounted on front (The left or right hand side available.)
o Bund ventilations.
o Front earth connection.
Standard Specification
o Self bunded with internal tank and external bund.
o Sloping floor design.
o Corner container lock castings.
o Internal ladder for access.
o 600mm manholes.
o Air breather vents for free venting.
o Secondary Containment(internal bund)
o Calibrated contents dip stick.
o Interstitial space dip stick.
o Top roof section designed to release water as it sits above the side rails of the tank.
o Additional sockets, doubler pad points available to suit applications.
o Unit sand blasted to SA2.5
o Paint three coats Hempel paint.
o Statutory signage.
Bulk Tanks
Intech build a range of bulk tanks a range of units without pump bunds, including ITP-75, ITP-90. These tanks have the same external dimensions as the standard tanks, however the removal of the pump bund increases the capacity stored. Details of the sizes and capacities are in TABLE. As a bulk storage tank – external folding platform is still required to check dips as well as service etc.
Flammable storage
Under Australian A.S. 1940 standards it is possible to store flammable products up to 55,000 litres in self bunded tanks.
Please check the local regulation and install relevant emergency vent for flammable storage.
