3M^™   Adhesive Transfer Tapes with Adhesive 300LSE  8132LE • 8153LE • 9453LE • 9471LE • 9472LE 9653LE • 9671LE • 9672LE

3M™ Adhesive Transfer Tape 9672LE 54 IN × 60 YD.

Product Description:

3M™ Adhesive Transfer Tapes with 3M™ Low Surface Energy Acrylic Adhesive 300LSE provides high bond strength to most surfaces, including many low surface energy plastics such as polypropylene and powder coated paints. The acrylic adhesive also provides excellent adhesion to surfaces contaminated lightly with oil typically used with machine parts.

Features:

• 3M™ Adhesive 300LSE is a hi-strength acrylic adhesive that provides a very high bond strength to most surfaces.
• Excellent bond to low surface energy plastics such as, polypropylene and powder coatings.
• Excellent adhesion to lightly oiled surfaces typical of machine parts.
• Thickness range of 2.0 mils, 3.5 mils, 5.0 mils and 8.5 mils for use on smooth, or rough surfaces.
• Extremely smooth adhesive for excellent graphics appearance.
• Double linered for selective die-cutting.
• Polycoated kraft liner for die-cutting end tabs and waste removed nameplates on a common carrier.
• 3M™ Adhesive Transfer Tapes 8132LE and 8153LE are double linered for selective die-cutting.

 Application Techniques:

For maximum bond strength, the surface should be thoroughly cleaned and dried. Typical cleaning solvents are heptane or isopropyl alcohol. Carefully read and follow manufacturer’s precautions and directions for use when using cleaning solvents.
Bond strength can also be improved with firm application pressure and moderate heat, from 100°F (38°C) to 130°F (54°C), causing the adhesive to develop intimate contact with the bonding surface.
Ideal tape application temperature range is 70°F to 100°F (21°C to 38°C). Initial tape application to surfaces at temperatures below 50°F (10°C) is not recommended for most pressure-sensitive adhesives because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory.

 General Information:

• Plastic nameplates or graphic overlays for use on low surface energy plastics.
• Waste removed nameplates on a common sheet for ease of application.
• Attaching membrane switch assemblies to powder coated surfaces and low surface energy plastics.
• Graphic overlays with end tabs for easy liner removal.
• Graphic application to surfaces such as wood, fabric, plastic, where very high bond strength is required.
• Attaching identification material to lightly oily surfaces typical of machine parts.

Applications Ideas:

Processing:
Slitting and die-cutting: This adhesive is very aggressive and may be difficult to convert depending on your application requirements. Chilling the adhesive between 35°F and 50°F will improve the processability. In addition, dies can be lubricated with Laminoleum evaporative stamping oil, which is available from Metal Lubricants Company (708-333-8900), or with Lubri-Blade 907 from Ceramic Technologies Inc. (800-258-8495). You may also refer to our Technical Bulletin on 3M™ Adhesive 300LSE converting. (70-0707-6205-2)
Roll Laminating: A combination of metal and rubber rollers with moderate pressure is recommended.

Product Use:

Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method of application.

 Other Products

Acrylic(VHB) Tape                                    3M 9495LE

Masking Tape                                           3M 467MP

Die Cutting

Certifications

Each roll packed with Poly bag / Blister card / Double blister in standard export cartons.