Product Details

PT212 Test Stand

PT 212 PT fuel pump Test bench is special equipment used to provide test and calibration for CUMMINS PT fuel pump. It has abundant functions, high measure precision, and fast sampling.

For instance: Fit for: PT(G), PT(G)VS, PT(G)MVS, PTGSVS, PTGAFC, PTGAFC-VS, PTR, PTH-VS fuel pumps etc and damping ASA valve.

Functions

1.Gear pump pressure and vacuum test

2. Idle speed test

3. Weight assistant pressure test

4. Pressure and flow test in every check point

5. AFC test

6. Oil stopping test 7. Route test of throttle

8. Oil return test of throttle

9. ASA valve test

10. EFC test

11. Shut down valve test

Main Features

Infinitely variable speed range of 450 to 4200 rpm
Dual scale flowmeter
Fitted with air flowmeter
Digital tachometer

Speed of Operation

Testing Cummins PT pumps on the HA123 is simple and fast. Everything about this test stand has been designed for operator convenience and speedy testing.

Accuracy

The digital, easy to read tachometer, flowmeters and gauges, together with close control of the test oil temperature ensures accurate test results.

Versatility

The HA123 Test Stand is supplied complete with all the necessary attachments to test the great majority of Cummins PT pumps.

Servicing

Maintenance is easy, the filters and test oil can be replaced in a very few minutes, there is only one greasing point.

Benefits

Test all types of Cummins PT pumps
Will test pumps fitted with A.F.C. and aneroid valves
Approved by Cummins

TECHNICAL SPECIFICATION

Motor

4kw (5hp) 3 Phase 50 or 60Hz with direct on starting. Motors for use outside the UK are wound for series – parallel operation to cover the widest possible voltage range.

Speed Range

450-4200 rpm.

Variable Speed Gear

Hartridge™ patented expanding pulley type, with single drive belt. Efficiency approximately 90% over full speed range.

Shaft Bearings

Ball bearings; pre-lubricated and sealed.

Tachometer

Digital

Accuracy +/-1 rpm over full speed range. Up-dates every 1/2 sec.

Gauges

Gear Pump Suction

Resilient Mounting

Gear Pump Pressure

Fuel Temperature

Manifold Pressure

Air Pressure

4 inch diameter 0-30 inches Hg

Acuracy +/- 0.2%.

3 inch diameter 0-800 lb/in2. (0-40 kg/cm2) accuracy 0.5%.

3 inch diameter; 50-150°F (10-65°C).

6 inch diameter 0-400 psi.

6 inch diameter 0-30 lb/in2. resilient mounting Accuracy +/- 0.2%.

Flowmeters

Continuous reading, dual scale, glass main flowmeter; individually calibrated 75 to 630 lb/hour and 600 to 2401 lb/hour; total scale length approx. 36 1/2 inches. Accuracy +/- 1%. Secondary glass flowmeter for throttle leakage; calibrated 75-750 cc/minute; scale length approx. 8 1/2 inches. Air flowmeter for measuring thread leakage.

Fuel Tank

5 Imperial gallons (22.5 litres) capacity; with 1 kw heater.

Temperature Control

Fuel temperature automatically controlled within +/- 2°F by electric heater and unique contra-flow water cooling system.

Fuel Filters

Main filter

Table drain

Disposable.

Fine mesh.

Writing Desk

Right hand or left hand fitting with paper retainer.

Electrical Supply

3 Phase 208-250V 50/60Hz
3 Phase 380-480V 50/60Hz

Additional Accessories

Each PT 212 Test Stand is supplied complete with all necessary accessories for testing the great majority of Cummins PT pumps, including AFC pumps and pumps fitted with aneroid valves. A side mounting bracket is available if required.