Specifications

non-crosslinked pe foam sheet extrusion line,ldpe foam sheet extrusion line,expanded pe foam sheet machine

NON-CROSSLINKED PE FOAM SHEET EXTRUSION LINE 

·  1.Screw: It is made of the top quality 38CrMnALA azotized steel. Thermal and azotized treatment and special surface plating made the screw with the characteristics of high intensity and long life. The screw diameter is 105mm

·  2. Cylinder: It is made with top quality 38CrMnALA azotized steel. Thermal treatment prevents wearing from long time service.

·  3. Material-Feeding Unit: Two ends are connected to the cylinder and the gear box. The raw material is sent to the extruder via here. The user should keep some cooling water in circulation in order to prevent the temperature arising, which will result in pastiness and agglomeration of the raw-material, even block the material-feeding hole.

·  4. Main-Motor of Extruder: The main motor is an adjustable AC motor, power 55KW.It is cooled by air. Main motor is connected to the screw in the main machine via the gear box.

·  5. Butane Input and Butane Pump: The butane pump is a high pressure measuring pump. This pump jets the deliquesced butane into cylinder by a high-pressure of 10-15Mpa (100--150Kg/cm).The butane mixes with the melted LDPE in the entrance of the machine cylinder. A non-return valve is equipped in the entrance of butane into the cylinder to insure the melted LDPE will never shoot back in case that the pressure in the cylinder is higher than the butane pressure. This is also to insure production safety.

·  6. Input of Shrinkage Resistant Agent and Shrinkage Resistant Agent Pump: Shrinkage resistant agent pump sends the heated shrink- resistant agent into cylinder with a pressure of 10-15Mpa (100-150mm/cm).The melted shrinkage resistant agent is mixed with LDPE in the shrinkage resistant agent's entering sector. A non-return valve is equipped in the entering sector to prevent the melted LDPE from shooting back in case that the pressure in the cylinder is higher than the shrinkage resistant agents. This is to insure the production safety.

·  7. Die-Head: Melted raw material is extruded from this head. The raw material started to froth at entering the die-lip. The thickness of the expanded PE sheet depends on the die lip and drawing speed.

·  8. Molding Drum: The width of the expanded PE sheet relies on this sector, so the cooling water or the cooling air should all be provided to this sector.

·  9. Haul-off: The sheets extended by the molding drum should be draught after entering this sector. At this time the drawing speed should keep balanced in order to insure the quality of the material. It is also equipped with a speed-changeable motor so as to timing the drawing speed.

·  10. Winding Roller: This part is equipped with a meter counter to set the sheet's length. It rotates 180 degrees when the winding length of the first roller reaches the set requirements. Then the second roller starts winding.

Model	90	105	120	130	170
ScrewΦ(mm)	90mm	105mm	120mm	150mm	170mm
Screw L/D (mm)	1:55	1:55	1:55	1:55	1:55
Production efficiency(kg/hr)	80-120kg/h	100-150kg/h	120-180kg/h	200-250kg/h	300-400kg/h
Product Thickness (mm)	0.5-3.5	0.5-6	0.5-8	2-12	2-18
Product Width (mm)	800-1200	800-1500	900-1700	1000-1800	1000-2500
Cooling	20-47	20-47	20-47	20-47	20-47
Cooling	Air/ Water cooling
Total Power (kw)	115kw	130	140	180	250
Screw REV(r/min)	20-80rpm	20-80rpm	20-80rpm	20-80rpm	20-80rpm
Dimensions(mm)	22000x2300 x2200	25000x2500 x2200	27000x2500 x2200	28000x2600 x2200	32000x2800 x2800
Total Weight (T)	5.5	6	6.5	7.5	9