N.W. 7.5 kgs ,
G.W. 8.5 kgs
Working pressure : 65 kgs
Max pressure : 90 kgs
Output : 6 L / Min
Mortor : 1000 W
Voltage : 220-240 V / 50 HZ , 110-120 V / 60 HZ
The correct use method of 220V high pressure cleaning machine:
This product has the advantages of simple operation, suitable for non professional cleaning, the absolute prohibition of the use in potentially explosive environments.
1 temperature between 5-40C.
2 cleaning machine consists of a motor and shockproof housing, the shape of the shell can move, and handle no protrusions and sharp, holding comfort.
3 cleaning machine gun, gun is provided with a handle, providing appropriate working position, shape and size depends on the handle effectively the safety regulations.
4 prohibit the use of any protective measures and changes in the water.
5 cleaning machine must use cold water (at least 11-12L/min), in order to continue working, serious damage to the pump seal ring air transfer. .
6 this product can be used for cleaning the Venetian blinds, door, car, cross-country car, yard, floor etc..
7 whenever the use of high pressure cleaning machine, suggested that gun in place, and a hand to hold the handle, on the other hand to seize the nozzle.
8 High pressure jet hand gun will produce recoil, ensure that when in use, you stand firm, firmly holding the gun.
Operating instructions:
In the connection on the washing machine electricity and water, according to the following steps:
1 check the "0/I" switch is in the "0" position, pull out the power plug.
2 with a strong matching pipe connection, matching pipe can withstand the pressure of at least 15bar/2000psi, inner diameter of at least 13mm..
The nozzle is mounted to the front end of the 3 gun.
4 connect the high-pressure hose and water, the water temperature should not exceed 60 degrees, fully open the inlet valve. .
5 press and hold the gun trigger, emptying the water in the air and waste.
6 connect the power plug and socket.
7 boot device, the 0/1 switch according to the position of the 1.
Warning: when the switch is off, washing machine Li Rengyou pressure, please do not directly facing the person water, otherwise the water may cause injury.
Gun safety device:
When the need to stop the machine, be sure to use the security on the gun safety "S", so as to avoid the machine is opened.
Motor.
Motor with thermal protection switch, if the temperature is too high, the motor will stop working automatically, wait 5-10 minutes can restart, if abnormal, please contact factory authorized service center.
The water from the container open in:
1 will open the container filled with water.
2 of the water inlet pipe end and the company provides quick connector link.
Container 3 hands hold the water inlet pipe 2 end into the water filled in the water inlet pipe full of water.
The 4 end is sinking vessel, (not floating) end link this product inlet connection.
5 in operation before, will the water air etc. the products within the high-pressure water outlet is normal, in the high pressure pipe joint is connected.
The nozzle 6 standard can be clockwise or counterclockwise nozzle to obtain a straight column.
7 will be inserted in the cleaning liquid filling gun, start washing machine, the cleaning liquid is automatically suction gun, mixed with water.
Close the cleaning machine:
1 the switch "0/1" to "0" position, and disconnect the plug and socket connection. Disconnect water source.
2 until the cleaning machine has no pressure to loosen the trigger gun, in order to prevent inadvertent opening, please use the safety gear.
Moving and storage:
Cleaning machine is on wheels, so it is easy to move.
Cleaning machine shall be stored in a room, if the storage environment is cold, or more than 3 months is not used before, suggest you to cleaning machine store, first antifreeze treatment (similar with the automobile antifreeze treatment).
In addition, to use, will be a little leakage, but this situation will disappear in a few hours after the. Take care not to damage the power line. Once the power line damage replacement power line the same, replace the power supply by professional personnel.
The user repair and maintenance instructions:
Warning: please switch off the power before the user to repair. Cleaning machine lubricating oil system closed, there is no need to add lubricating oil. Check regularly to avoid clogging.
The link member in the water off.
The high pressure hose high pressure port of unloading equipment.
Boot device, until the equipment inside the water without bubbles.
Shut off device, the high pressure hose and re installed to the device.
