The Ethernet over TDM 16E1 to Ethernet GFP Protocol Converter  is the IP ethernet over TDM converter, which supports the conversion from MAC frames to 1 – 16E1 lines. The maximum bit rate is 7.8Mbps (16E1 lines). The 16 E1 to Ethernet GFP Protocol Converter  not only provides alarms and status of the E1 line but also Ethernet interface together with advanced management functions, such as, throughput statistic of the Ethernet, but also supports the Unification Network Management via SNMP and GUI. Compliant to international standards, the device can communicate with products from other manufacturers adopting the same standards.

Ethernet over TDM 16E1 to Ethernet GFP Protocol Converter  picture:

nE1 interface

ØSupports automatic removal and recovery of E1 channels that used for carrying payload. The E1 channels that have urgent alarm, such as LOS and LOF, or the Bit Error Rate (BER) exceeds 1E-6, are removed automatically, and during this period, some Ethernet packets may be lost; It will be resumed when the fault dismisses .

ØSupports the embedded E1 BER Tester function, to detect any E1 channel of 8 channels. When the embedded E1 BER Tester is used via CLI command, the particular E1 channel on testing mode can not convey E1 service, while the other E1 channels are not affected by the BER test.

ØThe differential delay between any two of the 8 E1 can be up to 220ms; when the factual differential delay exceeds 220ms, alarm is generated and Ethernet is cut off.

ØJitter tolerance and jitter transfer characteristic compliant to ITU-T G.823.

nEthernet interface

ØProvides up to 8 shared Ethernet interfaces.

Ø1024 MAC address table and 5-minute aging time.

ØAccepts frames with length between 64 and 1916 bytes (otherwise filtering).

ØVLAN function based on tags compliant to IEE 802.1Q.

ØThroughout statistic of the Ethernet packets based on port, such as error packets.

ØConfigurable pause flow control .

ØOptional optical Ethernet interface compliant to IEEE 802.3u 100BASE-FX standard (can communicate with remote optical transceiver) and electrical Ethernet interface compliant to IEEE 802.3u 100 BASE-TX standard.

nManagement interface

ØGUI via serial RS232 port and telnet.

Ønetwork management platform based on SNMP(optional).

nTiming mode

ØOptional local timing mode and tracing E1 line (set by GUI).

ØThe source of tracing E1 line can be switched according to the signal quality. For instance, the system is set as tracing the first E1 link, when some malfunction occurs to it (i.e., urgent alarm LOS/AIS/LOF/LOMF or the signal is looped back), the system will automatically change to tracing the second E1 link; when the fault disappear, the system will be re-tracing the first E1 link.

nCompliant to ITU-T standards

ØGFP-F encapsulation recommendation G.7041.

ØVirtual concatenation(VCAT) and Link Capacity Adjustment Scheme (LCAS) recommendation G.7042.

ØEthernet to nxE1 mapping recommendation G.7043.

ØEthernet to single E1 mapping recommendation G.8040.

nBandwidth is increased without damaging the Ethernet data, and can be decreased no injury through management.

nThe E1s in the local and remote sides can be arranged arbitrarily, such as, the remote E1 port 1 can communicate with local E1 port 3.

nSupports bandwidth unbalanced usage – when some E1s cannot work properly (i.e. the bandwidth of the sending and receiving can be 2E1 and 3E1 respectively).

nProvides the E1 connection-ship between local and remote system (accessed via GUI).

nE1 tributary signal loopback automatic detect and cut off; when some E1 signal is detected as looped back, it will be not employed for carrying payload temporarily, and when the loopback is broken, this E1 will resume to be used.

nRemote/local E1 loopback function will be convenient for E1 line(transmission system included) testing.

nComplete alarm which is selectable to be shown between local and remote.

n Support AC 220V power or DC 48V power or double AC+DC power

nSingle-board design with small dimension, 1 U high and low power consumption.

 Application Diagram:

GUI Management Screen:

The goods warranty time is THREE years,we will provide best support by TEL,email,remote control or engineers in field.

Your any questions will be responsed within 12hours!