Overview
The 8E1 to ethernet converter is the IP ethernet over TDM converter, which supports the conversion from MAC frames to 8 E1 lines. The maximum bit rate is 15.8Mbps (8E1 lines). The 8E1 converter not only provides alarms and status of the E1 line but also Ethernet interface together with advanced management functions, such as, throughput statistic of the Ethernet, but also supports the Unification Network Management via SNMP and GUI .
Compliant to international standards, the device can communicate with products from other manufacturers adopting the same standards.E1 interface
Supports automatic removal and recovery of E1 channels that used for carrying payload. The E1 channels that have urgent alarm, such as LOS and LOF, or the Bit Error Rate (BER) exceeds 1E-6, are removed automatically, and during this period, some Ethernet packets may be lost; It will be resumed when the fault dismisses .
Supports the embedded E1 BER Tester function, to detect any E1 channel of 4 channels. When the embedded E1 BER Tester is used via CLI command, the particular E1 channel on testing mode can not convey E1 service, while the other E1 channels are not affected by the BER test.
The differential delay between any two of the 4 E1 can be up to 220ms; when the factual differential delay exceeds 220ms, alarm is generated and Ethernet is cut off.
Jitter tolerance and jitter transfer characteristic compliant to ITU-T G.823.
Ethernet interface
Provides up to 4 shared Ethernet interfaces.
1024 MAC address table and 5-minute aging time.
Accepts frames with length between 64 and 1916 bytes (otherwise filtering).
VLAN function based on tags compliant to IEE 802.1Q.
Throughout statistic of the Ethernet packets based on port, such as error packets.
Configurable pause flow control .
Optional optical Ethernet interface compliant to IEEE 802.3u 100BASE-FX standard (can communicate with remote optical transceiver) and electrical Ethernet interface compliant to IEEE 802.3u 100 BASE-TX standard.
Management interface
GUI via serial RS232 port and telnet.
network management platform based on SNMP(optional).
Timing mode
Optional local timing mode and tracing E1 line (set by GUI).
The source of tracing E1 line can be switched according to the signal quality. For instance, the system is set as tracing the first E1 link, when some malfunction occurs to it (i.e., urgent alarm LOS/AIS/LOF/LOMF or the signal is looped back), the system will automatically change to tracing the second E1 link; when the fault disappear, the system will be re-tracing the first E1 link.
Compliant to ITU-T standards
GFP-F encapsulation recommendation G.7041.
Virtual concatenation(VCAT) and Link Capacity Adjustment Scheme (LCAS) recommendation G.7042.
Ethernet to nxE1 mapping recommendation G.7043.
Ethernet to single E1 mapping recommendation G.8040.
Bandwidth is increased without damaging the Ethernet data, and can be decreased no injury through management.
The E1s in the local and remote sides can be arranged arbitrarily, such as, the remote E1 port 1 can communicate with local E1 port 3.
Supports bandwidth unbalanced usage ?when some E1s cannot work properly (i.e. the bandwidth of the sending and receiving can be 2E1 and 3E1 respectively ).
Provides the E1 connection-ship between local and remote system (accessed via GUI).
E1 tributary signal loopback automatic detect and cut off; when some E1 signal is detected as looped back, it will be not employed for carrying payload temporarily, and when the loopback is broken, this E1 will resume to be used.
Remote/local E1 loopback function will be convenient for E1 line(transmission system included) testing .
Complete alarm which is selectable to be shown between local and remote.
support AC 220V power or DC 48V power or double AC+DC power
Single-board design with small dimension, 1 U high and low power consumption.
8E1 to Ethernet GFP Converter
Place of Origin | China |
Model Number | BD-SEOP-8E1 /AC |
Product Features
You May Like
- Cisco Fiber Switches N9K-C93180YC-FX
- SIERRA AR7586
- Quectel LC29D GPS Beidou Inertial Guidance Module
- telit 4G module LE910C4-NF
- Acrel 4G LORA communication AWT200-1E4S1-4G/LR Intelligent data communication gateway, supports 4-way serial port
- Acrel Wireless communication terminal Supports centralized collection of up to 10,000 points AWT200-1E8SL
- Acrel 4G lora communication Data communication gateway 4-way serial port AWT200-1E4SL-4G/LR
- Acrel AWT200-1E4SL-4G/K smart gateway Can realize equipment monitoring, control and calculation Support breakpoint resume download
- Acrel intelligent gateway Support breakpoint resume download Can realize equipment monitoring, control and calculation AWT200-1E4SL-4G
- Acrel with Show buttons 1.2-inch dot matrix display and buttons AWT200-1E4SL Strong communication capabilities intelligent gateway
Popular Searches
usb bluetooth dongles
bluetooth adapter
bluetooth dongle
stereo receiver
bluetooth handsfree car kit
bluetooth car kit
bluetooth car kits
bluetooth receiver
bluetooth audio receiver
bluetooth key finder
Bluetooth Keyfinder
3km wireless wifi network
usb to tv adapter
usb car stereo adapter
bluetooth handsfree kit
bluetooth edr usb dongle
Find Similar Products By Category
You May Like
- Acrel 4G LORA communication Intelligent data communication gateway, supports 4-way serial port AWT200-1E4S1-4G/LR
- Acrel Supports on-site debugging-free and adaptive plagiarism. AWT200-1E4S1-4G/K smart gateway 4G communication with Switch
- Acrel AWT200-1E4S-4G 4G communication Wireless communication terminal Support data logical operations and processing
- Acrel Data communication gateway capable of real-time monitoring and discovery of abnormal data, large-capacity storage AWT200-1E4S
- Acrel timing control, remote control, local locking and other functions. 4P smart leakage circuit breaker ASCB1LE-63-C16-4P
- Acrel 2P ASCB1LE-63-C32-2P With short circuit over-temperature leakage and other protection functions intelligent leakage circuit breaker
- Acrel smart leakage circuit breaker 2P ASCB1LE-63-C63-2P Can monitor voltage, current, leakage and other parameters in real time
- Acrel smart leakage circuit breaker 2P ASCB1LE-63-C16-2P Guide rail installation, local electric control, remote control, etc.
- Acrel has timing control, remote control, local locking and other functions ASCB1LE-63-C32-4P smart leakage circuit breaker
- Acrel Intelligent leakage circuit breaker monitorcurrent voltage power leakage andother parameters in real time ASCB1LE-63-C63-4P
- Acrel ASCB1-M-CE LCD displaysupports event recording Parameter setting and control of each intelligent control smart gateway
- Acrel smart gateway can view the alarm, protection, fault and other status of each smart circuit breaker ASCB1-M-4G
- Acrel Communication management machine 1 channel 4G communication, 2 channels RS485, 1 channel LORA Anet-1E2S1-4G/LR
- Acrel intelligent gateway 1-way 4G communication 2-way RS485 communication support standard 8GB TF card Anet-1E2S1-4G
- Acrel 2-way RS485 1-way LORA support Max.64 devices multiple alarm setting for each device Anet-1E2S1-LR Low power consumption