ZONHOW 90 degree peeling strength testing machine
Introduction
- Digital type main adhesive tape peel strength tester by dongguan huakai detection equipment supply science and technology, the digital type main tape stripping force testing machine this machine is specialized in all kinds of tape stripping with 90 ° and 180 degree test and tensile.
- 90 degree peeling strength testing machine can do all kinds of paper, film, rubber, plastic, fabric, waterproof material, non-woven fabrics, metal wire, metal foil,. Metal mechanics, and the longitudinal and transverse tensile, tensile and tear properties and mechanical properties test, composite film, pressure sensitive adhesive materials such as stripping, splitting, shear strength test, elongation at break test, heat sealing tensile, tear, strength test, etc.
Additional application
- 1.Tested sample: plastic films, laminated materials, adhesive tapes, adhesive bandage (plaster), release paper, plastic films, leather, rubber & plastic, paper, fiber, etc.
- 2.Different test with different grips: tensile, peel, tear, heat seal, adhesive, bend and open force.
- 3.Deformation under defined load: Test deformation under defined load of tested sample
- 4.Load under defined deformation: Test load under defined deformation of tested sample
- 5.Software can issue word/excel report with results for max. force, elongation, tensile strength, peel strength, tear strength, compression strength, etc.
Conform to the standards
- GB/T2790 (adhesive 180 ° peel strength test),
- GB/T2791 (adhesive T peel strength test),
- GB2792 (pressure sensitive adhesive tapes 180 ° peel strength measurement),
- GB4850 (low-speed uncoil strength test),
- GB7754 (shear strength test),
- GB8808 (composite film peel strength test),
- ZBY28004 (determination of heat sealing strength),
- GB13022 (film tensile test),
- GB7753 (pressure sensitive adhesive tape tensile test)
Details show
Technical parameters
Range of speed | 50~500mm/min |
Effective force ranage | 0.4%~100% |
Motor | Panasonic sevor motor |
Resolution | 1/250,000 |
Capacity choice | 2,5,10,20,50,100,200Kg |
Effective tensile space | 650mm/800mm/1000mm(your choice) |
Accuracy | ±0.5% |
Force relative error | ±0.5% |
Displacement relative error | ±0.5% |
Test speed relative error | ±0.5% |
Accessories | computer, printer, system operation manual |
Operation method | windows operation |
Power | 220V ±10% 0.2KW/0.4KW |
Stroke protection | Upper and lower protection, prevent over preset |
Force protection | system setting |
Emergency stop device | Handling emergencies |
Test steps- ZONHOW 90 degree peeling strength testing machine
- 1. The tape stripping strength tester shall wipe the test board with the cleaning agent dipped in the wiping materials, and then wipe the test board with a clean degreased gauze. The test board shall be cleaned more than three times, until the working face of the board is cleaned through visual inspection.
- 2. Measure the width of the tape with a quantity of no less than 0.05mm.
- 3. Before making the sample, tear off the outer adhesive tape of 3-5 layers, and then take the adhesive tape of more than 200mm (the adhesive tape adhesive surface cannot contact hands or other materials).And glue the adhesive tape to the test board after cleaning.A polyester film of about 200mm long and 40mm wide or other material is placed under the other end of the test plate, and then the pressure roller is used to roll back and forth on the test sample for three times at a speed of about 300mm/min under self-weight (no air bubbles are allowed at the bonding point between the test sample and the test plate).
- 4. The sample should be stored in the test environment for 20 to 40 minutes after preparation.
- 5. The tape strip tester folded the free end of the sample 180 times and removed the bonding face 25mm from the test plate.The free end of the sample and the test plate are clamped on the upper and lower clamps respectively.The stripping surface should be consistent with the force line of the test machine.The machine was dissected continuously at a rate of 300mm/min plus or minus 10mm/min, and the stripping curve was plotted by the automatic recorder.
Features——ZONHOW 90 degree peeling strength testing machine
- 1. The tape stripping strength tester shall wipe the test board with the cleaning agent dipped in the wiping materials, and then wipe the test board with a clean degreased gauze. The test board shall be cleaned more than three times, until the working face of the board is cleaned through visual inspection.
- 2. Measure the width of the tape with a quantity of no less than 0.05mm.
- 3. Before making the sample, tear off the outer adhesive tape of 3-5 layers, and then take the adhesive tape of more than 200mm (the adhesive tape adhesive surface cannot contact hands or other materials).And glue the adhesive tape to the test board after cleaning.A polyester film of about 200mm long and 40mm wide or other material is placed under the other end of the test plate, and then the pressure roller is used to roll back and forth on the test sample for three times at a speed of about 300mm/min under self-weight (no air bubbles are allowed at the bonding point between the test sample and the test plate).
- 4. The sample should be stored in the test environment for 20 to 40 minutes after preparation.
- 5. The tape strip tester folded the free end of the sample 180 times and removed the bonding face 25mm from the test plate.The free end of the sample and the test plate are clamped on the upper and lower clamps respectively.The stripping surface should be consistent with the force line of the test machine.The machine was dissected continuously at a rate of 300mm/min plus or minus 10mm/min, and the stripping curve was plotted by the automatic recorder.
How to choose a suitable tensile tester ?
Regularly,we should focus on the force range, test speed, and test materials.
Computer controlled servo system | ||
Model | Force range | Test speed |
DZ-101 | 2~1000KG(10KN) | 0.001~500mm/min or 1000mm/min(optional) |
DZ-102W | 2~200KG(2KN) | 0.001~500mm/min |
DZ-103A | 2~500KG(5KN) | |
DZ-106 | 2~200KG(2KN) | |
DZ-101S | 5T~30T(300KN) | 0.1mm~250mm/min(regular test metal) |
DZ-101 DZ-102W DZ-103A DZ-106 DZ-101S
Touch screen controlled system | ||
Model | Force range | Test speed |
DZ-102 | 2~200KG (2KN) | 50~300mm/min or 0.001~500mm/min |
DZ-102WT | ||
DZ-103 | 2~5KN | |
DZ-104 | 2~10KN | |
DZ-110 | 2~20KN | 0.001~1000mm/min (Regular speed max is 500mm/min) |
DZ-102 DZ-102WT DZ-103 DZ-104 DZ-110
1. Are your company a trading one or a factory? Factory + trade (integration),12 years focusing on test instruments field,5 years exporting experience. OEM is also acceptable for us.
2. How to choose the most suitable products? Our professional team will give you the best suggestion as long as you tell us what kind of test you need to do and the required specification.
3. What’s the delivery term? Most of the time, we have stock in the factory. If there is no stock, normally, the delivery time is 15-20 working days after deposit receipt. If you are in urgent need, we can consider making a special arrangement for you.
4. Do you accept customization service? Yes, of course, we can not only offer standard machines but also customized machines according toyour request. Don’t hesitate to tell us your requirement, we will try our best to meet your needs.
5. Can we visit your factory before the order? Yes, we warmly welcome and sincerely invite you or your team to visit our factory, we will help to arrange a hotel and pick up you from the airport.
6. Do you have customers from our country before? Now our testing machines have been sold to more than 120 countries, like USA, Canada, Russia, UK, Italy, Germany, European Union, India, Pakistan, Philippines, Singapore, Thailand and Vietnam, Iran, Brazil and so on.
7.How about your warranty? Generally, our warranty is for one year. Within the warranty period, we can offer technical support and part parts change, necessarily, our engineers may go to your place for better service.
8.How about the packing for the machine, is it safely protected during transportation? Our machine is packed by standard export wooden box, it won’t be damaged. We’ve delivered many testing machines abroad by sea or by air without damage.
9. What is the order process? Inquiry - quotation - communication - order confirming - deposit payment - production - testing and debugging - balance payment - packing - delivery - customer receiving - after service.
10.How to install and use the product The product is shipped with operating instructions and video of the English version. |
Hi, this is Tracy from ZONHOW, China. We specialized in many different Lab testing machines. Warmly welcome to contact us share your cares. The following is my contact way, glad to see your inquiry.
| |
QQ number | 2355780557 |
+86 138 2570 4520 (It's very popular in China, and I do believe you will must be like it.) | |
Whats app | +86 13825704520 |
Skype | +86 138 2570 4520 |
TEL | +86 138 2570 4520 or +86 769 812-33466 |
Web | www.czhtest.com / 0755117.en.china.cn |