Introduction
35BYG Stepper Motor is based on the industry's advanced magnetic circuit design scheme，In the selection of materials, high-temperature permanent magnets and high-quality cold-rolled steel sheets are used, and Japanese NMB or NSK bearings are selected. The surface of the motor is sprayed or sealed with aluminum shell.
This series of motors have the characteristics of large output torque, low temperature rise, low noise, low vibration, and high reliability and stability. The motor runs smoothly and has no obvious oscillation area, which can meet the use of different working conditions in the automation industry.
Production process
Metalworking Stator→ Winding Stator→ Wiring Stator→ General Assembly→ Materiel→ Test & Packaging→ Warehousing→ Metalworking rotor
Electrical Specifications
| Model | Step angle (°) | Motor Length L(mm) | Rate Voltage | Rate | Phase | Phase | Holding | Lead | Rotor | Detent | Motor |
| (V) | Current | Resistance | Inductance | Torque | Wire | Inertia | Torque | Weight | |||
| (A) | (Ω) | (mH) | (g.cm) | (NO.) | (g.c㎡) | (g.cm) | (kg) | ||||
| 35BYG101 | 1.8 | 20 | 12 | 0.5 | 24 | 9 | 600 | 6 | 8 | 50 | 0.1 |
| 35BYG103 | 1.8 | 20 | 6.57 | 0.73 | 9 | 4 | 600 | 4 | 8 | 50 | 0.1 |
| 35BYG104 | 1.8 | 20 | 10.8 | 0.4 | 27 | 17 | 650 | 4 | 8 | 50 | 0.1 |
| 35BYG203 | 1.8 | 26 | 2.4 | 1.5 | 1.6 | 1.4 | 900 | 4 | 10 | 60 | 0.13 |
| 35BYG204 | 1.8 | 26 | 6.84 | 0.76 | 9 | 4.8 | 800 | 6 | 10 | 60 | 0.13 |
| 35BYG205 | 1.8 | 26 | 12 | 0.25 | 48 | 17 | 380 | 6 | 10 | 60 | 0.13 |
| 35BYG207 | 1.8 | 26 | 3.2 | 0.75 | 4.3 | 4 | 700 | 4 | 10 | 60 | 0.13 |
| 35BYG302 | 1.8 | 28 | 10.4 | 0.4 | 26 | 10 | 1000 | 6 | 11 | 80 | 0.14 |
| 35BYG303 | 1.8 | 28 | 7 | 0.54 | 13 | 9.5 | 800 | 4 | 11 | 80 | 0.14 |
| 35BYG304 | 1.8 | 28 | 3.5 | 1 | 3.5 | 3.5 | 1250 | 4 | 11 | 80 | 0.14 |
| 35BYG401 | 1.8 | 33 | 11 | 0.5 | 22 | 12 | 1000 | 6 | 13 | 95 | 0.17 |
Mechanical Dimensions
Wiring diagram
Quality control
1. Checking raw material before producing.
2. Checking one by one before the assebling
3. Checking one by one during the production
4. Have the random inspection before the delivery.