Specifications

Tungsten Wire Mesh

Tungsten is the most widely used of the refractory metals. In wire form, it is essential for the production of lighting products such as wire filament, and other goods where its high temperature properties are of use. Among its properties are a melting point of 3410ºC, a low coefficient of thermal expansion and low vapor pressure at elevated temperatures, along with good electrical and thermal conductivity.

material

machine

Stainless Steel -Stainless steel wire mesh material have SUS 201,202,304,316,316l ,310S 410 430 etc ,weave type:plain weave ,dutch weave ,twill weave ,plain dutch weave ,twilled dutch weave ,reversed dutch weave ,is widely used in chemical industry, environment protection, mine industry, airspace industry, paper-making, electronic industry, metallurgy industry, food industry, pharmacy etc, acid-resisting, alkali- resisting, heat-resisting and wear-resisting

Nickel - Nickel is widely used in woven wire cloth as a corrosion resistant medium. It protects itself by forming a passive oxide film, thus resisting corrosion in many oxidizing environments. In today's industry, nickel is replaced with stainless steel when Possible for cost savings.

Monel - This alloy is essentially non-corrodible. Composed of 67% nickel, 28% copper and 5% others. Monel is more corrosion resistant than copper in oxidizing conditions and more resistant than nickel under reducing conditions. Monel has good strength characteristics and has traditionally been used in food processing. As with nickel, it can be replaced with stainless steel.

Hastelloy B - This alloy is used for corrosion resistance to hydrochloric acid in most concentrations and at temperatures up to the boiling point. It is not recommended for high temperature service.

Hastelloy C-276 - This alloy is well suited to corrosion resistance service against strong oxidizing agents such as ferric chloride and cupric chloride. Good elevated temperature properties in the

1600 to 1800 range

Incoloy Alloy 800 - The nickel and chromium content here are similiar to Carpenter 20 Cb-3, while the copper and molybdenum content are reduced. Used in high temperature and corrosive environments.

Inconel Alloy 600 - 72% nickel and 15% chromium content makes Inconel 600 suitable for high temperature applications where corrosion resistance is important. Frequently used for heat-treating baskets.

Nichrome - A 60% nickel and 15% chromium alloy used in certain chemical conditions at temperatures up to 1700 Contains 1% silicon which helps keep scaling to a minimum. Subject to carbide precipitating characteristics.

Nichrome V - Similar to Nichrome, this alloy has a higher nickel content - 80% nickel and 20% chromium. It is used in severe chemical conditions at elevated temperatures up to 2000

FeCrAlY (commonly referred to as Hoskins 875 ® Hoskins Mfg Corp)C .03%  Cr 21-24%  Al 5-6%  Mn .50%  Si .2-1%  S .005%  P .03%  Y .01%  B .005%  Fe balance
FeCrAlY is a heat resisting alloy with excellent oxidation resistant characteristics. The addition of Yttrium inhibits scaling. This alloy has a maximum service temperature of 2430 F, but exhibits cold brittleness below 750-1200 F after service temperatures above 1000 F. Common uses are high temperature furnaces, radiant heaters, quartz heaters, and heating elements for toasters. 

packing :

our standard export seaworthy packing is as follows: wraped with"plastic film"as well as "waterproof paper" to prevent the moist while on sea,final loaded n wooden case or pallet to reduce the pressure while loading as required

                                                                             contact information

Contact person :Ms.Angile Wang

Mobile no:86-15833821075

Skype :angile1110

MSN:   angile1110

Company name :Anping Bolin Metal Wire Mesh Co.,Ltd.