Mini size electrical circular saw for cutting metal
tooth form:
roughing tooth and finishing tooth geometry
The specialists for difficult cutting.
Why so successful:
Special segments are ground radial and tangential. The relief grinding ensures good cutting clearance and avoids side pick-up on the tooth rim.
Solving problems for:
with segments made of HSS-DMo5. material no. 1.3343 with radial and tangential relief grinding |
Carbide Circular Saw Blade
Designed for accurate cuts at a higher cutting rate. This blade features the highest quality sawing grade of carbide.
Features
- Highest Quality Sawing Grade of Carbide
- State of The Art Manufacturing Equipment
- Tested and Proven Backing Material
- Unmatched Accuracy and Consistence from Tooth to Tooth
- Pioneers in The Manufacturing and Development of Carbide Blades
- Unmatched Consistency from Blade to Blade
Benefits
- Longest Possible Blade Life
- Higher Cutting Rate
- Minimal or No Warpage During Cutting Operation
- Lowest Cost per Cut in All Types of Material
- Minimal Burr Due to Consistent Chip-Load
- Accurate Cuts With a High Quality Surface Finish
Hints for the right use:
Particularly for cutting thin-walled AL-profiles on miter swingsaws.
The negativ tooth system is insensitive against impacts.
As a result the blade will not be attracted to the workpiece because it offers less resistance against the cutting piece. Especially for anodized profiles.
Used for manual feeding:
For structurals with a wall thickness of:
1 - 3 mm = NW
2 -10 mm = NX
Specifications may change without notice at the sole discretion of Angzi's Engineering Department
CERMET | ||
---|---|---|
Model | Blade Type | Size |
CM75 | TCB-CR | 285 mm x 2.0 mm x 60 teeth |
TCB-CR | 285 mm x 2.0 mm x 80 teeth | |
CM100 | TCB-CR | 360 mm x 2.25 mm x 60 teeth |
TCB-CR | 360 mm x 2.25 mm x 80 teeth | |
TCB-CR | 360 mm x 2.25 mm x 100 teeth | |
CM150 | TCB-CR | 460 mm x 2.7 mm x 40 teeth |
TCB-CR | 460 mm x 2.7 mm x 60 teeth | |
TCB-CR | 460 mm x 2.7 mm x 80 teeth | |
TCB-CR | 460 mm x 2.7 mm x 100 teeth |
TCB-CR: Former ST-3
Circular Saw Blade: TCB-TI
Carbide Tin Coated | ||
---|---|---|
Model | Blade Type | Size |
CM75 | TCB-TI | 285 mm x 2.0 mm x 60 teeth |
TCB-TI | 285 mm x 2.0 mm x 80 teeth | |
CM100 | TCB-TI | 360 mm x 2.25 mm x 60 teeth |
TCB-TI | 360 mm x 2.25 mm x 80 teeth | |
TCB-TI | 360 mm x 2.25 mm x 100 teeth | |
CM150 | TCB-TI | 460 mm x 2.7 mm x 40 teeth |
TCB-TI | 460 mm x 2.7 mm x 60 teeth | |
TCB-TI | 460 mm x 2.7 mm x 80 teeth | |
TCB-TI | 460 mm x 2.7 mm x 100 teeth |
TCB-TI: Former TI-3
Circular Saw Blade: TCB-CB
Carbide | ||
---|---|---|
Model | Blade Type | Size |
CM75 | TCB-CB | 285 mm x 2.0 mm x 60 teeth |
TCB-CB | 285 mm x 2.0 mm x 80 teeth | |
CM100 | TCB-CB | 360 mm x 2.25 mm x 60 teeth |
TCB-CB | 360 mm x 2.25 mm x 80 teeth | |
TCB-CB | 360 mm x 2.25 mm x 100 teeth | |
CM150 | TCB-CB | 460 mm x 2.7 mm x 40 teeth |
TCB-CB | 460 mm x 2.7 mm x 60 teeth | |
TCB-CB | 460 mm x 2.7 mm x 80 teeth | |
TCB-CB | 460 mm x 2.7 mm x 100 teeth |
TCB-CB: Former TA-3
Circular Saw Blade: TCB-SU
Carbide for Stainless | ||
---|---|---|
Model | Blade Type | Size |
CM75 | TCB-SU | 285 mm x 2.0 mm x 60 teeth |
TCB-SU | 285 mm x 2.0 mm x 80 teeth | |
CM100 | TCB-SU | 360 mm x 2.25 mm x 60 teeth |
TCB-SU | 360 mm x 2.25 mm x 80 teeth | |
TCB-SU | 360 mm x 2.25 mm x 100 teeth | |
CM150 | TCB-SU | 460 mm x 2.7 mm x 40 teeth |
TCB-SU | 460 mm x 2.7 mm x 60 teeth | |
TCB-SU | 460 mm x 2.7 mm x 80 teeth | |
TCB-SU | 460 mm x 2.7 mm x 100 teeth |
TCB-SU: Former TA-SUS
Circular Saw Blade: TCB-PT
Carbide for Pipe and Tube | ||
---|---|---|
Model | Blade Type | Size |
CM75 | TCB-PT | 285 mm x 2.0 mm x 60 teeth |
TCB-PT | 285 mm x 2.0 mm x 80 teeth | |
CM100 | TCB-PT | 360 mm x 2.25 mm x 60 teeth |
TCB-PT | 360 mm x 2.25 mm x 80 teeth | |
TCB-PT | 360 mm x 2.25 mm x 100 teeth | |
CM150 | TCB-PT | 460 mm x 2.7 mm x 40 teeth |
TCB-PT | 460 mm x 2.7 mm x 60 teeth | |
TCB-PT | 460 mm x 2.7 mm x 80 teeth | |
TCB-PT | 460 mm x 2.7 mm x 100 teeth |
TCB-PT
Specifications may change without notice at the sole discretion of Angzi's Engineering Department.
Q.Your price seems a little high?
A: You get what you pay for, our price is based on good quality.
A: Yes. We can make the machines with customers' brand and logo. With professional engineers,we can also design and produce the machines according to customers' requests.
Q:What about the lead time for mass production?
A:Honestly,it depends on the order quantity and the season you make the order,usually 3-13days, and many models of circluar saw blade have stock
Q:What about the payments
A:We usually accept 30%TT for deposit and 70%TT before shipment.
Q:What is your terms of delivery?
We accept EXW, FOB and CIF,you can choose the one which is the most convenient or cost effective for you
Q.What about the shipping ways?
A:We will choose the sea transportation,and if you want the blade saw,
we will choose the express like DHL,UPS,ect. or other shipping ways according to your requirement
Let's talk details!
.