Dissolvable Magnesium Alloys
In its quest to be the one of the first company to enable and provide a fully dissolvable frac plug OEM, Meifu has also developed dissolvable polymers, and super high-strength dissolvable metal matrix composites, that enable Meifu to be the company to offer materials to make a fully dissolvable plug.
Meifu has also developed a family of proprietary coatings, that delay dissolution of T dissolvable products to eliminate the possibility of premature dissolution while enabling longer laterals and protecting the Meifu dissolvable material from any acids or chemicals prior to perforation.
• Multiple extrusion production lines, up to 4000 tons capacity .
• Precisely controlled 3 intermediate-frequency induction furnaces to pre-heat the part before extrusion.
• Full set of extrusion dies: can extrude various sizes of Mg bars.
• Extensive machining capabilities.
• Can make most of the geometries for your components.
Grade | Mechanical Properties at Room Temperature | Dissolution Rate | Dissolvable Magnesium Alloy Type | ||||||
| Min. Tensile Strength | Min. Yield Strength | Min. Elongation | Hardness | ||||||
| MPa | Ksi | MPa | Ksi | % | HB | Test Conditions | mg/(cm2*h) | ||
| MF-96 | 380 | 55.2 | 300.0 | 43.5 | 5.0 | 96.0 | 93℃ 3%KCL | 40-65 | High temp./strength |
| MF-98 | 450 | 65.3 | 350.0 | 50.8 | 3.0 | 98.0 | 93℃ 3%KCL | 30-60 | |
| MF-982 | 450 | 65.3 | 350.0 | 50.8 | 3.0 | 98.0 | 93℃ 3%KCL | 15-23 | |
| MF-989 | 320 | 46.4 | 250.0 | 36.3 | 5.0 | 98.0 | 90℃ 3%KCL | 100-120 | |
| MF-916 | 380 | 55.2 | 260.0 | 37.7 | 3.0 | 101.0 | 50℃ 0.84%KCL | 20-35 | |
| 380 | 55.2 | 280.0 | 40.6 | 3.0 | 101.0 | 93℃ 3%KCL | 90-130 | ||
| MF-55 | 280 | 40.6 | 250.0 | 36.3 | 5.0 | 70.0 | 93℃ 3%KCL | 90-110 | |
| MF-88 | 120 | 17.4 | 80.0 | 11.6 | 35.0 | 65.0 | 93℃ 3%KCL | 200-400 | Low temp./ultra-high ductility |
| MF-105 | 250 | 36.3 | 180.0 | 26.1 | 12.0 | 75.0 | 93℃ 3%KCL | 30-55 | High temp./ductility |
| MF-85 | 250 | 36.3 | 180.0 | 26.1 | 12.0 | 64.0 | 93℃ 3%KCL | 40-70 | |
| MF-75 | 310 | 45.0 | 220.0 | 31.9 | 5.0 | 75.0 | 93℃ 3%KCL | 55-80 | |
| 50℃ 0.84%KCL | 15-25 | ||||||||
| MF-73 | 310 | 45.0 | 220.0 | 31.9 | 5.0 | 70.0 | 93℃ 3%KCL | 40-70 | |
| MF-741 | 300 | 43.5 | 250.0 | 36.3 | 6.0 | 70.0 | 93℃ 3%KCL | 130-220 | |
| 50℃ 0.84%KCL | 5-30 | ||||||||
| MF-63 | 210 | 30.5 | 150.0 | 21.8 | 15.0 | 62.0 | 93℃ 3%KCL | 70-100 | High temp./ultra-high ductility |
| MF-631 | 150 | 21.8 | 90.0 | 13.1 | 20.0 | 58.0 | 93℃ 3%KCL | 45-75 | |
| MF-613 | 150 | 21.8 | 90.0 | 13.1 | 24.0 | 55.0 | 93℃ 3%KCL | 20-55 | |
| MF-34 | 310 | 45.0 | 220.0 | 31.9 | 5.0 | 75.0 | 93℃ 3%KCL | 200-400 | Regular |
| 50℃ 0.84%KCL | 75-115 | ||||||||
| 50℃ 0.1%KCL | 40-60 | ||||||||
| MF-74 | 290 | 42.1 | 250.0 | 36.3 | 6.0 | 70.0 | 93℃ 3%KCL | 200-400 | |
| 50℃ 0.84%KCL | 80-110 | ||||||||
| 50℃ 0.1%KCL | 40-70 | ||||||||
| MF-43 | 220 | 31.9 | 180.0 | 26.1 | 8.0 | 64.0 | 93℃ 3%KCL | 120-160 | |
| 50℃ 0.84%KCL | 25-65 | ||||||||
| 50℃ 0.1%KCL | 5-30 | ||||||||
| MF-23 | 240 | 34.8 | 200.0 | 29.0 | 5.0 | 64.0 | 93℃ 3%KCL | 300-450 | |
| 50℃ 0.84%KCL | 50-120 | ||||||||
| 50℃ 0.1%KCL | 30-70 | ||||||||
| MF-13 | 240 | 34.8 | 200.0 | 29.0 | 5.0 | 55.0 | 93℃ 3%KCL | 500-800 | |
| 50℃ 0.84%KCL | 90-180 | ||||||||
| 50℃ 0.1%KCL | 40-80 | ||||||||
| MF-14 | 240 | 34.8 | 200.0 | 29.0 | 5.0 | 55.0 | 93℃ 3%KCL | 600-800 | |
| 50℃ 0.84%KCL | 120-300 | ||||||||
| 50℃ 0.1%KCL | 45-100 | ||||||||
| MF-15 | 240 | 34.8 | 200.0 | 29.0 | 5.0 | 55.0 | 93℃ 3%KCL | 700-1000 | |
| 50℃ 0.84%KCL | 150-350 | ||||||||
| 50℃ 0.1%KCL | 55-110 | ||||||||
