Production line of fully automatic melting and spraying machine
1: polymer feed
This equipment is equipped with automatic vacuum suction feeding device. Generally, the polymer is made into small spherical and granular slices. When the vacuum device is opened, the raw materials can be fed into the hopper equipped with the extruder.in
If the material in the hopper is low, please fill it up immediately. Otherwise, the material will be broken and the melt spray cloth will become thin or not mesh.
2: molten extrusion
At the feeding end of the screw extruder, the polymer slice shall be mixed with the necessary raw materials such as additives. After mixing, the polymer slice shall enter the screw extruder and be heated to melt. Pay attention to the heating temperature
According to the characteristics of the raw material to be adjusted, can be in accordance with the manufacturer's recommended parameter Settings, can also be adjusted in accordance with the actual production requirements, so that the finished products to meet the use requirements.
3: fiber formation
The filtered clean melt should pass through the filter screen and then be evenly fed into the spinneret to make the extrusion amount of each spinneret consistent
When the volume, need to stop the machine to check whether there is a fault, check whether the filter screen is blocked, timely troubleshooting problems, so as not to damage the extrusion equipment.When eliminating extruder problems, check
The filter plate of the spinneret can observe whether the holes in the filter plate have impurities that cannot flow normally.The fibers are pulled out of the melt by the crosswind, the spinnerets are squeezed out of the glue, and then cooled.
4: electrostatic electret
After the net through the electrostatic device, so that the melt - spraying non - woven fabric with static electricity.PM2.5 particles and other isolation mainly through two ways: mechanical blocking and electrostatic adsorption.Among them, mechanical block main
It is to use the small pores of the filter material of mask fiber to block the invasion of bacteria and viruses, but this mechanical blocking effect is very bad for the filtration effect of particles with particle size less than 1 m, so it cannot work
To urification.Therefore, in order to improve the filtration efficiency of the mask, the electrostatic adsorption capacity of the mask can be increased.And increase the capacity of mask electrostatic adsorption, the need to melt spray non - spinning
Cloth filter material for electret treatment.After electret treatment, the surface of the fiber will be charged with a large amount of static electricity
Add breathing resistance.
6: slitting and winding
There is rewinding equipment at the end of the production line.The fusion-sprayed non-woven fabric is cut and rolled up to the size required for packaging.Winding has tension control device, so that the winding material is always stable
Volume status.Before the rewinding is equipped with a cutting knife, which can remove the edge material, so that the packaging specifications for packaging, of course, can also be cut into the size of the product production, the distance between the cutting knife is non-woven
The width of the finished product, this distance can be adjusted, according to the production needs to adjust and arrange the number of cutting knives
You May Like
- melt-blown fabric guangzhou melt-blown fabric india zhenjiang melt-blown fabric
- melt blown non-woven fabric nonwoven bfe99 95 melt-blown fabric melt-blown belt
- 3 ply facemask melt-blown non-woven fabric non-woven fabrics and the melt blown fabric
- pp intermediate melt-blown non-woven fabric intermediate melt-blown non-woven fabric brazil melt-blown-nonwoven-fabric
- intermediate melt-blown non-woven fabric melt-blown non-woven fabric brazil melt-blown non-woven fabric raw material
- melt-blown nonwoven fabric cutting machine filtert-blown fabric non-wonen fabric
- medical filter melt-blown fabric melt-blown fabric in turkey bfe99 melt-blown nonwoven fabric
- electrostatic melt-blown fabric melt-blown fabric mould melt blown none-woven fabrics
- melt-blown fabric 99 fabric heater fabric mold
- pp melt blown non-woven fabric production line melt-blown melt blown fabric melt-blown non-woven nonwoven fabric making machine
Popular Searches
Find Similar Products By Category
You May Like
- pp granules melt-blown fabric mask melt-blown fabric making machine melt-blown nonwoven fabric making machine
- 10/20m melt-blown nonwoven waterproof fabric fabric production line polypropylene nonwoven fabric
- melt-blown fabric shantou fabric making machine heater for melt-blown fabric
- melt-blown non-woven fabric fabric n95 air filter fabric cutting machine
- melt-blown nonwoven fabric melt blown non-woven fabric melt-blown fabric machine
- melt blown fabric nonwoven machine melt blown pp fabric machine melt blown fabric production machine
- pp melt blown spun bond non woven fabric machine king machine melt-blown fabric machine melt blown fabric
- melt blown fabric for mask machine 600mm melt blown nonwoven fabric machine pp melt-blown nonwoven fabric making machine
- melt-blown fabric rewinding machine pp melt blown nonwoven fabric machine melt blown fabric manufacturing machine
- pp melt blown spunbond nonwoven fabric machine pp melt blown non woven fabric making machine melt blown fabric machine nonwoven
- bfe99 melt blown nonwoven fabric machine machine to manufacture melt blown fabric melt blown nonwoven fabric machine ruain
- pp melt blown fabric making machine melt blown non woven fabric making machine melt blown non woven fabric machine
- mask melt blown fabric filter making machine melt blown machine fabric mask melt blown fabric making machine
- melt blown fabric making machine melt-blown fabric machine melt blown nonwoven fabric making machine
- melt blown nonwoven fabric machine melt blown fabric machine pp melt blown nonwoven fabric machine