Performance and Features

 

Its main features are as follows:

 

1. The use of 32-bit ARM microcontrollers, hardware integration, high reliability has been further improved;

 

2. LCD LCD is 480x272, with backlight, Chinese, English and other languages optional interface operation, and can be on-site options to facilitate plant commissioning test machine;

 

3. The screen protection screen with a hard acrylic material, better wear and scratch resistance;

 

4. The use of silicone panel and buttons, to adapt to high and low temperature environment stronger;

 

5. With RS485 communication interface, the use of MODBUS protocol can achieve the "three remote" function;

 

6. With CAN BUS interface, you can connect with the J1939 EFI machine can not only monitor the common data EFI machines (such as water temperature, oil pressure, speed, fuel consumption, etc.), or by CANBUS interface control starting, stopping, acceleration and deceleration, etc;

 

7. suitable for three-phase four-wire, three-phase three-wire, single-phase two-wire, two-phase three-wire (120 / 240V) power 50 / 60Hz system;

 

8. collect and display mains / generator phase voltage, phase current, frequency, power parameters;

 

9. City of electrolysis column with perfect protection, over frequency, under frequency, overvoltage, undervoltage, the frequency rate of change, the vector angle change;

 

10. Generation with overvoltage, undervoltage, over frequency, under frequency, over current, over power, reverse power, phase, reverse phase sequence function;

 

11. Synchronization parameters are: power generation and mains voltage difference, the difference between power and mains frequency, power and mains phase angle difference;

 

12. In automatic mode with a variety of operating modes: automatic mains failure boot, islanding mode, input, constant power output, peak shear mode, the load receiving mode;

 

13. In a parallel / load transfer function soft splitting;

 

14. The three fixed analog sensors (temperature, oil pressure, level);

 

15. The two programmable analog sensor can be set to the temperature or pressure or level sensors;

 

16. A variety of temperature, pressure, oil level sensor curve can be used directly, and custom sensor curve;

 

17. The precise collection of various parameters of the engine;

 

18. The control and protection functions: automatic diesel generator set start / stop switch sub-gate fault display and perfect protection functions;

 

19. All outputs are relay outputs;

 

20. parameter settings: allows users to change the setting of its parameters, and memory in the internal EEPROM memory, when the system is powered down it will not be lost. Most of these parameters can be adjusted from the controller front panel, all parameters can be used to adjust the PC via the USB interface, but also the use of a PC via RS485 interface adjustments;

 

21. A variety of starting conditions (speed sensor, hydraulic, power generation) option;

 

22. Power supply a wide range (8 ~ 35) VDC, can adapt to different starting battery voltage environments;

 

23. The historical record, real time clock, timer switch (monthly / weekly / boot once a day and can be set with or without load) function;

 

24. With the cumulative run A, B and cumulative energy A, B, the user can remove the accumulated again, user-friendly self-statistics;

 

25. a heater, cooler, fuel pump control functions;

 

26. have a maintenance function, maintenance time can be set to the action (warning, alarm or trip down down);

 

27. All parameters are used in digital adjustment, eliminating the conventional analog potentiometer adjustment method to improve the reliability and stability of the machine;

 

28. The design of rings of rubber seal between the housing and the control panel, waterproof up to IP55;

 

29. Fixed controller with a clamp metal clamps, excellent performance at high temperatures;

 

30. The modular design, fire-retardant ABS shell, removable terminal blocks, embedded installation, compact, easy to install.

 

 

Q1: Are you a factory or trading company?
A1: We are a factory, we can guarantee our price is first-hand, very cheap and competitive.

 

Q2: How does your factory do regarding quality control?
A2: All the products will be 100% checked before the shipment.

 

Q3: When can I get the price?
A3:Usually we quote within 24 hours after we get your inquiry.

 

Q4: How could I get a sample?
A4: if you can not buy our product in your local area, we will ship a sample to you.You will be charged a sample price plus all related shipping costs.Express delivery charge depends on the quantity of the samples.

 

Q5: What is the price of shipping?
A5: Depending upon the port of delivery, prices varies.