Motor type | Output Power | Voltage | Load | Speed | Rated Torque | Efficiency | Noise | IP Class |
KW | V | A | RPM | Nm | % | dB | ||
VOL-BL2K0B48 | 2 | 48 | 44.80 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B72 | 2 | 72 | 29.87 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B110 | 2 | 110 ac | 11.29 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B220 | 2 | 220 ac | 5.64 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B380 | 2 | 380 ac | 3.27 | 3000 | 6.37 | 93 | 62 | IP 54 |
VIEW MORE PLS CONTACT US >>>
Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped.
What to do: Replace the fuse or reset the breaker.
Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.
Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.
Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.
Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.
Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.
Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.
Q: Motor takes too long to accelerate,what to do?
A: Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.
Likely cause: Brushes are worn.
What to do: Verify brush length.
Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.
Q: Motor runs in the wrong direction,what to do?
A: Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.
Q: Motor runs OK but has a clicking noise,what to do?
A: Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.
You May Like
- 1000rpm 3HP 6 poles synchronous PMSM Brushless DC motor
- 220V 3000rpm 200W Permanent Magnet Brushless DC Motor
- IEC 5HP 3750W 220Vac 3 phases synchronous motor PMSM motor
- Brushless 5HP 220v 3750W PMSM Brushless DC motor
- high voltage 375W 3000rpm permanent magnet dc motor
- 3000rpm 200w permanent magnet brushless dc motor with 63S IEC size
- 3 phasev 3HP 220Vac Rare earth Nd-Fe-B permanent magnet PMSM brushless DC motor
- 3000rpm 200W 220V Permanent Magnet Synchronous brushless DC Motor
- 1500rpm 200w permanent magnet synchronous Electric Brushless DC Motor
- IEC standard 63S 3000rpm 200w permanent magnet synchronous brushless DC motor
Popular Searches
Find Similar Products By Category
You May Like
- IEC 3000rpm permanent magnet synchronous motor 200w
- 4p. 350w 3000 rpm 4kw 380v spindle n52 neodymium magnet continuous electric brushless DC motor
- IEC 1/4HP 110V 200W Permanent Magnet DC Motor
- 36 v 80mm 2500w helicopter control external rotor brushless dc motor for window air conditioner
- 150cc 1400rpm three phase tricycl radiator kipas pendingin motor brushless motor dc for power tool
- Energy Saving 72V 4000W Brushless DC Motor for Auto
- IEC 220Vac PMSM motor for air cooler
- IEC 80 low noise 3000rpm 220V 750w brushless dc motor
- 220Vac 5HP 1500rpm aluminum brushless dc motor for drone
- Low noise 6 poles 3hp 1000rpm 2250W 6.42A permanent magnets IEC dc brushless motor
- IE 3 high voltage IEC 0.2kw 0.58A 1500rpm brushless dc motor drone
- high torque 1000rpm 187W 0.55A brushless dc motor with EC 71
- IEC standard 6P 375w 1000rpm 1.09A 220Vac dc brushless wheel hub motor
- 220Vac 3HP 1500rpm IEC standard 4 Poles small brushless dc motor
- IE 4 high powerful 220Vac 3000rpm 10.7A 3.75KW brushless dc motor