Trade Assurance! 10kw wind generators wind turbine generator price, 10kw wind turbine manufacture, Wind electric generator pma
FD8-10kw wind turbine: US4300.00/set
FD10-10kw wind turbine: US$4800.00/set
1. 10kw Wind turbine model selection
Horizontal axis, directly drive, fixed pitch, auto furling wind turbine, FD8-10kw, FD10-10kw.
Permanent magnet generator, 3 phrase AC
3 pcs FRB blades, high efficiency, low noise
FD10-10kw wind turbine work in low average wind speed place lower than 6.5m/s;
FD8-10kw wind turbine work in normal average wind speed place 6.5m/s-8m/s.
New designed 10kw wind turbine, pitch controlled, auto eletric controlled by controller, tailless new model work in rich wind speed place.
2. 10kw Wind turbine spec
10KW fixed pitch wind turbine, horizontal axis, directly drive, 3 pcs blades wind turbine
8m, 10m blades rotor for different wind condition place
Blades with protection film, which makes blades work life more longer than normal blades
grid connection system/batery charge system
Lattice tower, stand alone tower, hydraulic tower
Tower height optional
Provide tower foundation drawing design
Low noise level
Provide 10kw blades, generator, tower, controller with dump load, grid tie inverter, pure sine wave inverter seperately
FD8-10kw wind turbine normal data:
| Model: | FD8-10kw |
| Rotor Diameter: | 8m |
| Number of Blades: | 3pcs |
| Material of Blades: | Fibre glass expoxy |
| Cut-in wind speed: | 3m/s |
| Working wind speed: | 4-30m/s |
| Survival wind speed: | 50m/s |
| Rated wind speed: | 12m/s |
| Rated rotate speed: | 180r/min |
| Rated output power: | 10kw |
| Max output power: | 20kw |
| Type of tower: | Manganese steel independence tower |
| Type of generator: | Permanent-magnet 3 phrase AC |
| Speed regulation method: | Yaw+ auto furling |
| Stop method: | manual brake + eletric auto brake |
| Working voltage: | 360v/380vdc optional |
| Tower height: | 15m or optional |
| Wind turbine main body weight: | 650kg |
| Life span: | 20 years; |
| Warranty: | 3 years after installation |
FD10-10kw wind turbine normal data:
| Model: | FD10-10kw |
| Rotor Diameter: | 10m |
| Number of Blades: | 3pcs |
| Material of Blades: | Fibre glass expoxy |
| Cut-in wind speed: | 3m/s |
| Working wind speed: | 4-30m/s |
| Survival wind speed: | 50m/s |
| Rated wind speed: | 10m/s |
| Rated rotate speed: | 190r/min |
| Rated output power: | 10kw |
| Max output power: | 15kw |
| Type of tower: | Manganese steel independence tower |
| Type of generator: | Permanent-magnet 3 phrase AC |
| Speed regulation method: | Yaw |
| Stop method: | Brake by hand drag |
| Working voltage: | 360v/380v |
| Tower height: | 15m |
| Wind turbine main body weight: | 800kg |
| Measurement(CBM): | 6.3CBM |
| Life span: | 15-20 years; |
| Warranty: | 3 years |
www.huayaturbine.com
Blades, hub for the wind turbine:
Wind turbine assembly
3. FD10-10kw wind turbine Output power data
| Rated power (w) | Wind speed (m/s) | Rotation speed(r/min) | Working voltage(V) | Output power(W) |
| 10000 | 3 | 66 | 132 | 460 |
| 4 | 83 | 155 | 1015 | |
| 5 | 94 | 178 | 1702 | |
| 6 | 111 | 106 | 2377 | |
| 7 | 128 | 235 | 3298 | |
| 8 | 148 | 284 | 4924 | |
| 9 | 164 | 339 | 7010 | |
| 10 | 189 | 363 | 10101 | |
| 11 | 196 | 369 | 10507 | |
| 12 | 208 | 374 | 10858 | |
| 13 | 211 | 380 | 11160 | |
| 14 | 215 | 382 | 11350 | |
| 15 | 218 | 385 | 11650 | |
| 16 | 220 | 389 | 12060 | |
| 17 | 220 | 389 | 12380 | |
| 18 | 220 | 389 | 12380 | |
| 19 | 220 | 389 | 12380 | |
| 20 | 220 | 389 | 12380 |
4. Wind turbine freatures
| 1. Blade: Manufacturing according to the airscrew structure principle and techniques. |
| Optimal wide TSR & High L/D ratio. With protection film on the edge, long work life. |
| Select blade type by wind tunnel testing. |
| With high efficiency, low noise. |
2. Blades rotor: Hub adopts casting molding; Blades rotor and generator adopt universal connection, directly driven. |
| Connection is reliable, durable, smooth operation without vibration. |
| 3. Generator |
Rotor: Nd-Fe-B permanent magnet. Prefabricated tangential magnetic circuit rotor; High magnetic flux density, small |
| cubage, good manufacturing process and high performance. |
| Adopt SKF, NSK bearing. |
| Close transmission slip ring, the cable will not enlace. |
| 4. Speed regulation: yaw. Simple, reliable and safety. |
| 5. Anti-corrosion treatment: All the outside parts are designed to anti-salt, anti-fog, anti-atmospheric |
| anti-sandstorm corrosion design. |
6.Tower: guy wire tower, tilting up tower, standalone tower, hydraulic tower… It can be designed according to your request. |
| 7. 300w-2.5kw auto braking; 3kw-30kw auto braking system and manual braking system. |
| 8. Wind turbine design principle is simple, safety, reliable, maintenance free. |
| 9. Provide low wind place, rich wind place solution. Wind turbine OEM service. |
5. 10kw wind turbine Working system
Wind turbine on grid system: wind turbine with tower + PWM on grid controller with dump load + grid tie inverter
Wind turbine off grid working system:
wind turbine with tower + PWM off grid charge controller with dump + battery group + inverter;
Wind solar hybrid off grid system, diesel or grid power as backup power
6. 10kw fixed pitch wind turbine advantage
Fixed pitch wind turbine including: 3 pcs blades, nose cone, hub, generator with manual brake part, nacelle, tail rod, tail vane
- Low/normal average wind speed wind turbine
- Fixed pitch,auto yaw, auto brake, manual brake protection system.
- Low cost, reliable and steady working system
- Low start up wind speed 3m/s, low rated wind speed 10m/s;(FD10-10kw)
- Low noise level, provide noise drawing chart
- High efficiency 3 phrase AC permanent magnet generator
- Vacuum mould blades with protection film, long worklife span in sand wind condition
- Wind turbine with antiseptic treatment, hot-galvanize tower. It can be work in sea side, island, lake...
- stand alone tower is easy to installation for sample order; Hydraulic tower is easy to install for bulk order.
- We provide completely on grid system kit
Home, farm, signal station, island, garden...
8. Blades,pma
Vacuum mould blades with protection film
C.W blades, low noise level, high efficiency
FRB material, 3 pcs blades per set
Adjust blades rotor balance before delivery
Iron cast housing made by losting mould. Beautiful and antirust. Rare earth material, high efficiency and low start up torque
9. Tower type: stand lone tower, hydraulic tower (optional)
Tower height can be manufacture according to user's request.
The tower with hot-galvanize.
We provided the tower foundation drawing after confirm the tower type, tower height.
10. Matched controller
Controller converts 3 phase AC power to Dc and charge to the battery group or feed to the grid tie inverter.
Controller with auto brake function, PWM voltage stablization function.
Matched with off grid single phrase/ 3 phrase pure sine wave inverter.
On grid system grid tie inverter ABB power one inverter, our provided grid tie inverter.
10kw 120v wind turbine + 3kw solar power off grid controller normal spec:
Wind turbine power (W) | 10KW |
Solar panel power (W) | 3KW |
Battery | 120 |
Operating mode | Continuous |
Function | Rectifier,Charge, control |
Display mode | LCD |
Display content | Wind turbine voltage, wind turbine current, wind turbine power, solar panel voltage, solar panel current, solar panel power, battery voltage, charge current |
Operating environment | Temperature -30-60℃,humidity≤80% |
Relative humidity | <90% No condensation |
Noise (1m) | <40dB |
Degree of protection | IP20(Indoor) |
Cooling method | Forced air cooling |
*Communication interface (optional) | RS485/USB/GPRS/Ethernet |
*Temperature compensation (optional) | -3~-5mv/°C/2V,Accuracy:±1°C |
PWM dump load voltage (v) | >140V |
Dump load 1voltage of the wind turbine (v) | 150V±5 |
Recovery charging voltage of the wind turbine (v) | 135V±5 |
Power shortage of the battery (V) | 100V±5 |
Solar stop charge voltage(V) | 150V±5 |
Recovery charging voltage of the solar(v) | <140V |
Self-provided connecting wire of the battery (mm²) | >16mm² |
Self-provided connecting wire of the three-phase dump load (mm²) | >10mm² |
Self-provided connecting wire of the PWM dump load (mm²) | >10mm² |
PWM fuse (A) | 100 |
Solar fuse(A) | 40 |
Charging fuse (A) | 125 |
10kw wind turbine on grid system controller normal spec:
Type | 10KW |
Wind turbine rated power | 10KW |
Wind turbine Max. power | 20KW |
Function | Rectifier, control, dc output |
Display mode | LCD |
Display content | Wind turbine voltage, wind turbine current, wind turbine power, Solar panel voltage, solar panel current, solar panel power, DC output voltage, output current, output power |
PWM constant voltage | ≥480dc |
3-phase dump load voltage of the wind turbine | 560±5Vdc |
Time-lapse of the wind turbine 3-phase dump load | 12-20 min |
Low-voltage | ≤200Vdc |
PWM dump load fuse | 32A |
DC output fuse | 40A |
Work environment temperature | -30-60°C |
Relative humidity | <90% No condensation |
Noise (1m) | <40dB |
Degree of protection | IP20(Indoor) |
Cooling method | Forced air cooling |
*Communication interface (optional) | RS485/USB/GPRS/Ethernet |
*Temperature compensation (optional) | -4mv/°C/2V,-35°C~+80°C, Accuracy:±1°C |
Size of the controller | 655*480*320 mm |
Weight of the controller | 26Kg |
Size of the dump load | 760*520*550 mm |
Weight of the dump load | 38Kg |
11. Matched (3 phase )grid tie inverter 15k. pure sine wave inverter single phrase/ 3 phase
Inverter output voltage, frequency can be manufactured according to different countries request.
Wind turbine main body, blades, pma, tail, controller, inverter: plywood case
Tower: soft packages
Delivery by sea, by air
FOB/C&F, CIF
500w-3kw wind turbine : 3-5 working days after payment
5kw-30kw wind turbine: 7-10 working days after payment
50kw-60kw 15-20 days after payment
Tower needs about 10 working days after payment
| Item | Description | Packing | G.W(Kg) | ||
| Packing method | outside size(m) | ||||
| 1 | Hub,nose cone and under cover | plywood box | 0.68*0.71*0.77 | 48 | |
| 2 | Generator/rotor body | plywood box | 2.06*1.14*0.72 | 670 | |
| 3 | Blades | plywood box | 3.58*0.59*0.42 | 140 | |
| 4 | Tail vane | Tail vane plate | plywood box | 2.08*1.28*0.32 | 270 |
| Tail vane frame | |||||
| Giant-shaped steel & others | |||||
| 5 | Tail rod | soft package | 3.3*0.54*0.14 | 75 | |
| 6. | On grid controller | carton | 0.570*0.550*0.330 | 26.5 | |
| 7. | Unload box | carton | 0.770*0.550*0.460 | 34.5 | |
| TTL: | 4.35 | 1264 | |||
Provide professional wind turbine technical support;
Provide on/off grid system design, wind solar hybrid system design service.
Completely system provider and designer;
Wind turbine type, model, capacity selection professional support;
Tower design, foundation drawing support;
Provide Pma, hub, flange drawing;
Provide OEM service, customized service.
Support paypal /west union payment, TT payment;
We started to manufacture wind turbine in 1994. In 2004, there are only 4 small wind turbine manufactures in China. We keep improving and develop in the small wind turbine field. We are not the leading small wind turbine exporter, but we are the leading wind turbine manufacture and designer now.
We manufacture 300w-30kw fixed pitch wind turbine;
2kw, 3kw, 5kw, 10kw, 20kw, 30kw, 50kw, 60kw pitch controlled wind turbine;
On grid system/off grid system, wind solar hybrid system; Water heating system;
For more details, pls contact with us via e-mail.
Certification and test report
1. Wind turbine model selection
It depends your local annual average wind speed, daily/monthly home power consumption.
Low average wind speed place, select larger blades rotor, higher rated working voltage;
Rich wind place select speed limited wind turbine: variable pitch wind turbine, stall out vertical axis wind turbine.
The safety and steady working system is the first choice.
2. Wind turbine tower selection
Now we have guy wire tower, stand alone tower, tilting up tower, hydraulic tower.
Guy wire tower cost is lower, easy to delivery. But the installation area is larger;
Tilting up tower is for 500w-5kw wind turbine. Easy installation, small installation area. But the delivery cost is higher.
Hydraulic tower: It is used for no crane place. Easy installation and put down. The cost is higher.
Stand alone tower for the installation place with crane.
The tower height: Make sure blades rotor is higher than wind turbine surrounding barrier height.
3. Working system selection
On grid system: wind turbine with tower + PWM controller with dump load + grid tie inverter;
Off grid system: wind turbine with tower + PWM charge controller with dump load + battery group + inverter;
Wind solar hybrid on/off grid system: Safety and reliable than only wind or solar system.
Wind turbine water heating system: work in rich wind place. Average wind speed higher than 8m/s.
For more question, pls contact with us directly. We will give you a professional response.
Why select us:
We are the wind turbine designer and manufacture. We know our wind turbine advantage and disadvantage in different wind condition.
I have more than 10 years wind turbine sales experience. We provide the right wind turbine and working system to different user according to their different situation and request.
In 2004, there are 4 small wind turbine manufacture. Now there are so much trading company and manufacture, we know Chinese small wind turbine market well and can provide user more useful advise.