"Analysis of common failures of air compressors
The environment has poor ventilation and heat dissipation. There are three main situations in which the surrounding environment of the air compressor affects heat dissipation: one is that it is too close to a wall-like obstacle; the other is that there are other heat sources near the air compressor, and the third is that the front door and side door of the Ingersoll Rand air compressor parts are open during operation, and the fan Strong air currents cannot be formed.
(2) The radiator is blocked. When the surrounding environment of the air compressor is dusty, long-term operation will cause a layer of dust or sludge to adhere to the surface of the radiator, and the internal copper pipe is also easy to be blocked due to the accumulation of grease, which affects the heat dissipation effect.
(3) The oil filter is too dirty. This machine has 3 side-by-side oil filters. When they are too dirty, the resistance oil cannot enter the compressor at the normal flow rate, and the compressor will quickly heat up due to insufficient cooling and lubricating oil. When the pressure difference between the inlet and outlet oil exceeds 0.18MPa, the filter element needs to be replaced.
(4) The cooling oil level is too low. When the cold machine is checked, if the oil level is lower than the lower end of the inspection tube, it should be replenished immediately.
(5) Low oil mark or poor oil quality. The machine uses the manufacturer’s special compressor oil. When other low-grade or inferior oils are used, the viscosity and specific heat will not reach the standard and the temperature will be too high.
(6) The fan tape is broken or loose. When the tape breaks, the air compressor will automatically stop when the temperature is too high after running for about 5 minutes. If the tape is too loose, it will slip, which will reduce the fan speed and affect heat dissipation. At this time, the tightness of the fan tape should be replaced or adjusted.
(7) The oil shutoff valve is out of order. There is an oil cutoff valve between the oil filter and the compressor. When the oil cutoff valve cannot be opened, due to no oil lubrication and cooling, the temperature of the compressor rises rapidly after starting, and it will automatically stop after about 1min. Remove the temperature plug at the exhaust end of the compressor, you will find that the plug is dry and oil-free, and blue smoke will flow out of the hole. Open the maintenance hole at the bottom of the air compressor, remove the oil shut-off valve, and gently move the valve stem with your fingers to see if it can be pushed forwards and backwards and can be easily reset. If it is difficult to move or return, you need to further disassemble the oil shut-off valve. If there is grease on the valve stem or valve hole, it needs to be polished with fine sandpaper until it can slide easily; if the spring is broken or there is a foreign object stuck in the letter, it will also affect the movement of the valve stem. At this time, you need to replace the spring or clean the spring and spring seat.
(8) The filter element of the oil and gas separator is too dirty. When it is too dirty, the oil will affect circulation due to excessive resistance, causing overheating and shutdown. This situation is judged from the pressure difference before and after loading. When the pressure difference between the two ends is 3 times the initial pressure or the maximum pressure difference reaches 0.1 MPa, it should be cleaned or replaced.
(9) The thermostat bypass valve is in the open position. The thermostat bypass valve is in the open position when the machine is cold, and gradually closes when the temperature rises. When it fails, it may always be in the open position, and the cooling oil flows directly back to the air compressor from here without passing through the radiator, so the temperature will slowly rise and stop. The maintenance method is similar to that of the shut-off valve.
(10) Exhaust pressure is too high. When the exhaust pressure exceeds the rated 12MPa, the compressor and diesel engine will heat up and stop automatically when the compressor and diesel engine are overloaded for a long time. At this time, first check and adjust the pressure valve, and then check the diesel engine throttle control system and eliminate this fault. "
amlpp0215@gmail.com / Shanghai Amlpp Co., Ltd
Wechat : shamlpp
SP300E05V STAUFF Small machine lubricating oil filter
SP100E05B STAUFF Anti-fuel EH oil system oil return
SP100E05V STAUFF Times oil filter
SP200E03B STAUFF Oil filter
SP200E03V STAUFF Parker filter
SP300E03B STAUFF Pall filter
SP300E03V STAUFF Imported replacement filter element
SP100E03B STAUFF Return oil filter element
SP100E03V STAUFF Three in parallel
SP200E10B STAUFF Turbine oil motive filter element
SP200E10V STAUFF Lubricating oil filter element for small oil station
SP300E10B STAUFF Vickers Oil Filter
SP300E10V STAUFF Dasheng filter
SP100E10B STAUFF Feedwater pump coupling oil station filter element
SP100E10V STAUFF Parker filter
SP200E20B STAUFF EH oil system oil return
SP200E20V STAUFF Times oil filter
SP300E20B STAUFF Oil filter
SP300E20V STAUFF Parker filter
SP100E20B STAUFF Pall filter
SP100E20V STAUFF Imported replacement filter element
SP200E05B STAUFF Return oil filter element
SP200E05V STAUFF Three in parallel
SP300E05B STAUFF Turbine oil motive filter element
SP300E05V STAUFF Lubricating oil filter element for small oil station
SP100E05B STAUFF Vickers Oil Filter
SP100E05V STAUFF Dasheng filter
SP200E03B STAUFF Feedwater pump coupling oil station filter element
SP300E03B STAUFF Main oil pump suction inlet filter element
SP300E03V STAUFF Diatomite filter
SP100E03B STAUFF Prasey filter
SP100E03V STAUFF Pall filter
SP200E10B STAUFF Power plant filter
SP200E10V STAUFF Coalescing filter
SP300E10B STAUFF Diatomite filter
SP300E10V STAUFF High pressure oil station filter
SP100E10B STAUFF Dongqi hydraulic oil motive filter element
SP100E10V STAUFF Main engine lubricating oil double filter element
SP200E20B STAUFF Oil filter
SP200E20V STAUFF Coal pulverizer reducer cold oil device filter element
SP300E20B STAUFF Suction filter
SP300E20V STAUFF Turbine impurity removal filter element
SP100E20B STAUFF Self-circulating filter element
SP100E20V STAUFF Lubrication filter
SP200E05B STAUFF Xinhua Hydraulic Filter
SP200E05V STAUFF Air compressor air filter
SP300E05B STAUFF Ice machine essential oil filter
SP300E05V STAUFF Suction filter
SP100E05B STAUFF Suction filter
SP100E05V STAUFF Xinhua Oil Station Filter
SP200E03B STAUFF filter
SP200E03V STAUFF Oil and gas separation filter
SP300E03B STAUFF Crude oil filter
SP300E03V STAUFF Fine filtration
SP100E03B STAUFF Dewatering filter
SP100E03V STAUFF Coal pulverizer filter
SP200E10B STAUFF Blower oil station filter
SP200E10V STAUFF Slurry circulating pump reducer filter element
SP300E10B STAUFF Combined filter
SP300E10V STAUFF Coal mill oil station filter element
SP100E10B STAUFF Oil filter
SP100E10V STAUFF Coalescing filter
SP200E20B STAUFF Small machine lubricating oil filter
SP200E20V STAUFF Induced fan motor oil station filter
SP300E20B STAUFF Outlet filter element
SP300E20V STAUFF Main oil pump inlet filter element
SP100E20B STAUFF Mahle filter
SP100E20V STAUFF Imported filter element
SP304E06B STAUFF anti-fuel anyway
SP304E03B STAUFF Coal mill oil station filter
