"Analysis of common failures of air compressors
The environment has poor ventilation and heat dissipation. There are three main situations in which the surrounding environment of the air compressor affects heat dissipation: one is that it is too close to a wall-like obstacle; the other is that there are other heat sources near the air compressor, and the third is that the front door and side door of the Ingersoll Rand air compressor parts are open during operation, and the fan Strong air currents cannot be formed.
(2) The radiator is blocked. When the surrounding environment of the air compressor is dusty, long-term operation will cause a layer of dust or sludge to adhere to the surface of the radiator, and the internal copper pipe is also easy to be blocked due to the accumulation of grease, which affects the heat dissipation effect.
(3) The oil filter is too dirty. This machine has 3 side-by-side oil filters. When they are too dirty, the resistance oil cannot enter the compressor at the normal flow rate, and the compressor will quickly heat up due to insufficient cooling and lubricating oil. When the pressure difference between the inlet and outlet oil exceeds 0.18MPa, the filter element needs to be replaced.
(4) The cooling oil level is too low. When the cold machine is checked, if the oil level is lower than the lower end of the inspection tube, it should be replenished immediately.
(5) Low oil mark or poor oil quality. The machine uses the manufacturer’s special compressor oil. When other low-grade or inferior oils are used, the viscosity and specific heat will not reach the standard and the temperature will be too high.
(6) The fan tape is broken or loose. When the tape breaks, the air compressor will automatically stop when the temperature is too high after running for about 5 minutes. If the tape is too loose, it will slip, which will reduce the fan speed and affect heat dissipation. At this time, the tightness of the fan tape should be replaced or adjusted.
(7) The oil shutoff valve is out of order. There is an oil cutoff valve between the oil filter and the compressor. When the oil cutoff valve cannot be opened, due to no oil lubrication and cooling, the temperature of the compressor rises rapidly after starting, and it will automatically stop after about 1min. Remove the temperature plug at the exhaust end of the compressor, you will find that the plug is dry and oil-free, and blue smoke will flow out of the hole. Open the maintenance hole at the bottom of the air compressor, remove the oil shut-off valve, and gently move the valve stem with your fingers to see if it can be pushed forwards and backwards and can be easily reset. If it is difficult to move or return, you need to further disassemble the oil shut-off valve. If there is grease on the valve stem or valve hole, it needs to be polished with fine sandpaper until it can slide easily; if the spring is broken or there is a foreign object stuck in the letter, it will also affect the movement of the valve stem. At this time, you need to replace the spring or clean the spring and spring seat.
(8) The filter element of the oil and gas separator is too dirty. When it is too dirty, the oil will affect circulation due to excessive resistance, causing overheating and shutdown. This situation is judged from the pressure difference before and after loading. When the pressure difference between the two ends is 3 times the initial pressure or the maximum pressure difference reaches 0.1 MPa, it should be cleaned or replaced.
(9) The thermostat bypass valve is in the open position. The thermostat bypass valve is in the open position when the machine is cold, and gradually closes when the temperature rises. When it fails, it may always be in the open position, and the cooling oil flows directly back to the air compressor from here without passing through the radiator, so the temperature will slowly rise and stop. The maintenance method is similar to that of the shut-off valve.
(10) Exhaust pressure is too high. When the exhaust pressure exceeds the rated 12MPa, the compressor and diesel engine will heat up and stop automatically when the compressor and diesel engine are overloaded for a long time. At this time, first check and adjust the pressure valve, and then check the diesel engine throttle control system and eliminate this fault. "
amlpp0215@gmail.com / Shanghai Amlpp Co., Ltd
Wechat : shamlpp
RP200E03B STAUFF Diesel filter
RP200E05B STAUFF Glass fiber hydraulic filter
RP200E10B STAUFF Natural gas filter element for gas gathering station
RP200E20B STAUFF Forklift diesel filter
RP240E03B STAUFF CAT excavator engine filter filter
RP240E05B STAUFF Generator set air filter
RP240E10B STAUFF Pipeline hydraulic oil filter
RP240E20B STAUFF Rotary line filter
RP300E03B STAUFF Hygroscopic air filter
RP300E05B STAUFF Excavator diesel filter
RP300E10B STAUFF Hydraulic suction filter element
RP300E20B STAUFF Gearbox filter element
RP050E03B STAUFF Diesel filter element
RP050E05B STAUFF Marine air filter
RP050E10B STAUFF Hydraulic suction filter
RP050E20B STAUFF Large flow filter
RP080E03B STAUFF Return oil filter
RP080E05B STAUFF Japan RRR Precision Filter
RP080E10B STAUFF Dana filter element hydraulic oil
RP080E20B STAUFF Line gap filter
RP090E03B STAUFF suction filter
RP090E05B STAUFF Agricultural machinery excavator parts diesel filter
RP090E10B STAUFF Air filter element filter
RP090E20B STAUFF Magnetic oil return filter element
RE200G03B STAUFF Fuel filter element
RE200A03B STAUFF Air compressor oil filter
RE200G05B STAUFF Excavator hydraulic oil return filter element
RE200A05B STAUFF Roller hydraulic oil filter
RE200A05B STAUFF New Holland Air Filter
RE200B100B STAUFF Farm machinery generator set filter element
RE200S100B STAUFF Slag conveyor hydraulic oil filter
RE200G10B STAUFF Oil Filter Element for Marine Diesel Generator Set
RE200A10B STAUFF Diesel filter element for Caterpillar roller paver
RE200G20B STAUFF Emerald hydraulic oil filter
RE200G20B1650 STAUFF Hydraulic oil filter element of filter element bending machine
RE200A20B STAUFF Wind power gearbox oil filter
RE200B25B STAUFF Hydraulic filter element for construction machinery equipment
RE200S25B STAUFF Demag injection molding machine hydraulic oil filter
RE200B50B STAUFF Terex respiratory filter
RE200S50B STAUFF Pilot filter
SP120E03B STAUFF Hydraulic drain filter
SP120E05B STAUFF Allison imported gearbox filter
SP120E10B STAUFF Cutting fluid filter
SP120E20B STAUFF PP filter element
SP140E03B STAUFF Wire wound filter
SP140E05B STAUFF Folding microporous filter element
SP140E10B STAUFF Activated carbon filter
SP140E20B STAUFF Double section filter
SP160E03B STAUFF Stainless steel filter element
SP160E05B STAUFF Electricity production
SP140E20B STAUFF Ocean purification
SP160E03B STAUFF Automobile fuel filter
SP160E05B STAUFF Oil filter element
SP160E10B STAUFF Hydraulic oil filter
SP160E20B STAUFF Polypropylene melt blown filter
SP010E03B STAUFF Metallurgical Industry
SP010E05B STAUFF Textile industry
SP010E10B STAUFF Engineering locomotive
SP010E20B STAUFF car
SP020E03B STAUFF Agricultural locomotive
SP020E05B STAUFF laboratory
SP020E10B STAUFF Integrated filter
SP020E20B STAUFF Split filter
SP010F03B STAUFF Ceramic filter
SP010F10B STAUFF resin filter element
SP010F20B STAUFF Titanium rod filter
SP020F03B STAUFF RO reverse osmosis filter
SP020F10B STAUFF clip-on filter element
SP020F20B STAUFF Ultrafiltration membrane filter element
SP110E03B STAUFF Nanofiltration cartridge
SP110E05B STAUFF air filter
SP110E10B STAUFF Pharmaceutical industry
SP110E20B STAUFF Food and beverage industry
SP170E03B STAUFF Oil industry
SP170E05B STAUFF electronics industry
SP170E10B STAUFF chemical industry
SP170E20B STAUFF RO reverse osmosis membrane filter
SP250E03B STAUFF Suction filter
SP250E05B STAUFF Pipeline filter
SP070E05BOBE STAUFF
SP130E05BOBE STAUFF
SP070F03BOBE STAUFF
SP070F20BOBE STAUFF
SP130F03BOBE STAUFF
SP130F20BOBE STAUFF
SP035F10B STAUFF
SP250F10B STAUFF
