502 best extra strong instantv non toxic super glue cyanoacrylate adhesive in bulk

 

 

NAN PAO RESINS CHEMICAL CO., LTD OFFICE: 3F, 356, SEC.1, NEIHU ROAD, NEIHU DIST., TAIPEI CITY, TAIWAN, R.O.C.  TEL 886-2-25942172  FAX  886-2-25964485 FACTORY:No.12, NAN HAI VILLAGE, SHEE KANG SHANG, TAINAN, TAIWAN, R.O.C

 

 

Cyanoacrylate Adhesive  

^For Wood & Plastic

DESCRIPTION

 

GW-01Fis a high strength, top fast setting adhesive which can be used for virtually any type of fastening job. GW-01Fhas become one unique product featuring with the fastest setting ability in the realm of Cyanoacrylate Adhesive. GW-01Fis specially designed for bonding and repairing of wooden furniture. Better efficiency and quality combined with cost saving have made GW-01Fto be a substitute for repair material. When a thin layer of GW-01Fapplied between two surfaces comes into contact with atmospheric moisture, a rapid polymerization occurs producing the ultimate bond.

 

PHYSICAL PROPERTIES

 

Liquid State	Cured State
Base                       Ethyl Cyanoacrylate	Color                                      Clear
Color                                  clear	Specific Gravity(25oC)                      1.1~1.3
Specific Gravity(20oC)              1.053~1.060	Softening Point( o C)                     80 (176 OF)
Refractive Index ( n  )                   1.439	Refractive Index( n  )                        1.439
Flash Point (oC)                      80(176oF)	Dielectric Constant(@ 10MHz)                   2.5
Shelf Life                           6 Months	Dielectric Loss(@ 10MHz)                     0.067
Boiling Point(o C)                   65/6mm Hg	Soluble in Acetone, Dimethyl formamide, romethame, Dimethyl sulfoxide
Viscosity(cps)…………….………………..1.8 - 5

 

DIRECTIONS  FOR  USE

 

1. 1.     Make sure the surfaces to be bonded are clean and dry(preferable to solvent-wipe plastics

, glass, and rubber, and to acid-treat metals).      

1. 2.     Dispense a drop or drops to one surface only. Apply only enough to leave a thin film after

compression.

1. 3.     Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate

bond develops in less than one minute.(Maximum strength is achieved in 24 to 48 hours).

1. 4.     Wipe off excess adhesive from the top of the container and recapGW-01F if left uncapped, may

deteriorate by contamination from moisture in the air.

1. 5.     Because GW-01F condenses by polymerization, sometimes a whitening will occur on the surface of the container or the bonded materials. Should this happen, wipe surfaces well with acetone.

 

 

 

 

 

 

 

 

 

 

BOND STRENGTH

 

(TENSILE SHEAR STRENGTH, CURED FOR 24 HOURS AT 20-25℃(68-77^oF)

KG/CM2		KG/CM2
Rigid PVC to Rigid PVC	40-60	SBR to SBR	5-10
ABS to ABS	50-70	Steel to Steel	150-190
Polycarbonate to Polycarbonate	80-120	Stainless steel to Stainless steel	150-180
Polystyrene to Polystyrene	30-45	Aluminum to Aluminum	140-170
Natural rubber to Natural rubber	5-9	Copper to Copper	130-150
*Neoprene to Neoprene	5-9	Steel to Rigid PVC	50-60
NBR to NBR……	5-9	Stainless steel to Neoprene	5-10
ABS to SBR…………….	5-10

 

CURE SPEED

 

GW-01F             Seconds		Seconds
ABS to ABS	3-5	NBR to NBR	2-5
Wood to Wood	20-30	Stainless steel to Stainless steel	3-5
ABS to Stainless steel	3-5	ABS to NBR	2-5
NBR to Stainless steel	2-5	Wood to ABS	5-10

 

PRECAUTION

 

1. 1.           Use with proper ventilation. Avoid contact with skin and eyes.
2. 2.           If contact with skin occurs, rinse with warm water or dissolve gradually with solvent such as acetone, dimethylformanide, or nitromethane. Do not try to remove forcibly.
3. 3.           If adhesive gets into eye, keep eye open and rinse thoroughly. Seek medical attention immediately.
4. 4.           Keep well out of reach of children.
5. 5.           Keep adhesive in a cool, dry place 20-25℃(68-77^oF). For long term storage, refrigeration (5^oC or 40^oF) is recommended.