the multiply wooden acoustic panel ues for wall decorating, ceiling decorating, suspended ceiling and partition and improve sound articulation.
it suitable used in:
s, recording rooms, listening rooms, rehearsal rooms and more professinally interspace timbre projects.
2.theaters, indoor gymnasiums, discos, KTV rooms and more performance and entertainment location.
eting rooms, offices, halls, hotels and more sound absorption and secrecy projects.
4.air-port, railways, bus-stops, manufactories, workshops and more noise reduction projects.
the section configuration of multiply wooden acoustic panel: substrate, felt and surface.
1)substrate(basal material): based on high quality of 12/15/18mm MDF with density of 750kg/m3, mix ceramics, gypsums, cements or other minerals.
more choices for basal material:HDF, E1 ECO-friendly MDF and Fireproof MDF(B1 grade).
2)feld: acoustic fleece, pasted on the back of the panel, noise reducible and fire resistant(made in CHINA, GERMANY AND FRANCE)
3)surface: available in three different finishes: real wood veneer, printed wood melamine finished and fireproofing surface.
2.there are two patterns of LIYIN WOODEN ACOUSTIC PANEL: one pattern named "GROOVY PANEL", the other named"PERFORATION PANEL".
1)"GROOVY PANEL" is made up of a series of grooves on the surface and the other side is made of a series of round holes.
general patterns: 13-3(the rate of perforating is 12%); 14-2(the rate of perforating is 7%); 28-4(the rate of perforating is 7.5%); and 38-4; 59-5.
size: 2440mm*128mm or customer's request.
thickness: 12/15/18mm.
2)"PERFORATION PANEL" is made up of a series of holes to the MDF.
general patterns: 32/32/3-25mm; 16/16/3-8mm(the holes machined over the MDF with 3-25mm diameter,the centre-to-centre distance between the holes is 32mm or 16mm.)
size: 600mm*600mm; 600mm*1200mm; 1200mm*2440mm or customer's request.
thicknes: 12/15/18mm
color:
installation:
1,PREPARING
1)constructing location: keep dry, the temperature should be higher than 10'C, the widest humidity range should confined to 40%-60% after construction 24 hours before constructing, the location should reach the standards as above.
2)acoustic panels: for the acoustic panels accommodated to the circumstance of constructing, please place the panels in the constructing location for 48 hours, check up the type, specification and amount of the panels before constructing.
3)keels: fix the keels on the wall flatly according to the plan, the keels should be flat, slick, no rust, no metamorphosis; the wall must be construct according to the standards, the keels suitable install with acoustic panels, leave smaller than 500mm space between each wooden keel(smaller than 600mm of light steel keel), install the keels vertically with acoustic panels.
2,FIXING
1)siz of wall: all panels should be installed in accordance with the manufacturers recommendations.
2)cutting: all necessary hardware and accessories for a complete job installation are to be furnished by the contractor.
3)install the acoustic panels: the installation of acoustic panels should be carried out in a sequence from the left to the right, from upside to downside, the panels are cut to fit on site, traditional woodworking tools are suitable for cutting the panels, if panels are cut using a fine tooth table saw the panels should be cut face up to avoid scratching and at a much slower speed to avoid any tearout or chipping.
4)fix on keel:
1)wooden keel fixing using nails, staples or screws into prefixed timber battens on the walls via the tongue and groove joint.
2)also can fixing by: Light Steel Keel(size: 18*26*3000mm, use clip(size: 45*38mm) to fix.(needs 2.1m of keel and 17 clips per m2)